How to tell plunge router bits from non-plunge router bits.

Collapse
X
Collapse
  •  

  • How to tell plunge router bits from non-plunge router bits.

    Do you guys know your router bits?

    Do you know how to tell a plunge bit from a non-plunge bit?

    A non plunge bit has cutters around the periphery, but not the center. It can enter grooves from the side and cut moving sideways.
    Click image for larger version  Name:	straight bit no plunge.JPG Views:	0 Size:	13.1 KB ID:	841749
    A plunge bit has cutters that go all the way to the center of the bit face. It can cut moving vertically as well as sideways.
    Click image for larger version  Name:	plunge bit2.jpg Views:	0 Size:	35.2 KB ID:	841750Above see the bar across the center as well as the two edge cutters? Without this bar, when you drive the bit straight down the dead spot in the middle will prevent plunging (just burns) unless you crush the wood. Can't use a non plunge bit on a plunge router to enter a hole vertically... like you would for a lettering template bit or a stopped groove where you have to drop the bit in vertically and then move it sideways. It has to cut its way in on the plunge, then cut on the side when you move it.

    Here is another pictorial anatomy of a plunge bit
    Click image for larger version  Name:	plunge bit.JPG Views:	0 Size:	18.8 KB ID:	841751
    Note that the following round nose bits are plungeable because the cutters go all the way to the center.
    Click image for larger version  Name:	round nose bits.JPG Views:	0 Size:	32.5 KB ID:	841752
    Attached Files

    • cwsmith
      #2
      cwsmith commented
      Editing a comment
      Thanks Loring,

      As usual, you always bring knowledge and wisdom to this forum.

      Thanks and Merry Christmas to you and your family,

      CWS

    • leehljp
      #3
      leehljp commented
      Editing a comment
      Unfortunately, (or is it fortunately?) I learned that in the school or hard knocks. I have owned a plunge router since the mid '80s and quickly learned the necessities of a full cutting edge around the bottom. But it has only been since Loring posted the thread on signs that I started using brass guides. https://www.sawdustzone.org/forum/di...sign-lettering

      Before that, I made jigs for the base of the router to guide the plunge and cuts.

      That said, My mind has been running wild with templates for plunge and inlays. I started looking at templates and they are expensive and not nearly as creative (wide a variety) as I would like, Then it dawned on me after doing a couple of signs: I have a good Scrollsaw and I can do graphics fairly well on the computer, and size them accordingly - just make my own. I also thought of choosing my own fonts and scroll sawing a set in the perfect size on the Scrollsaw. It would not be difficult to print out the letters the size of the bushing/guides and attach them with spray adhesive to 1/8" plywood to cut out.

    • Jim Frye
      #4
      Jim Frye commented
      Editing a comment
      When I bought my first router (early 90s), it was a Ryobi R700 plunge router. I didn’t have much money for tools back then and bought router bits from the same mail order house (Trend Lines) that I bought the router. They had an in house line of bits that I used because they were much less than the other bits available. All of the straight bits had the extra cross cutter at the end. Never gave it a second thought until years later when I bought a Bosch straight bit that lacked the cross cutter. Yes, I had been plunge cutting with the old bits for years. They worked well enough that I never considered buying any of those spiral bits.
    Posting comments is disabled.

Latest Articles

Collapse

  • How to identify a Ryobi BT3000/BT3100/Craftsman 22811 or 21829 clone saw by sight
    by LCHIEN
    So you want to buy a BT3 clone. Been out of production for a while. Shopping on Craigs list or for sale ads is hard

    You have to keep an eye out and you have to be used to spotting the appearance giveaway features of the various models... Ryobi BT3000, BT3100, Craftsman 22811 and 21829
    There are certain things that clue you in and there are many ads that don't give model numbers and have crappy photos. Search for keywords RYOBI, Precision, System are often used in ad listings and
    ...
    12-20-2022, 01:53 AM
  • How to tell plunge router bits from non-plunge router bits.
    by LCHIEN
    Do you guys know your router bits?

    Do you know how to tell a plunge bit from a non-plunge bit?

    A non plunge bit has cutters around the periphery, but not the center. It can enter grooves from the side and cut moving sideways.

    A plunge bit has cutters that go all the way to the center of the bit face. It can cut moving vertically as well as sideways.
    Above see the bar across the center as well as the two edge cutters? Without this bar, when you drive the...
    12-22-2020, 04:09 AM
  • Festool Domino Settings for Evenly Spaced Mortises
    by twistsol
    I was in the shop this weekend and was trying to figure out the math for the settings on the Festool Domino to space the mortices evenly and centered across a cabinet front to back. After a bunch of trial and error with my math, I gave up and got close enough and cut the Domino slots for most of the cabinets before my shop time ran out. It was still bugging me, so I figured it out on the plane on the way to work.

    Very simply, we need to subtract the width of all mortises created from...
    01-29-2018, 12:46 AM
  • Sharpening Woodworking Chisels
    by Sam Conder
    While attending a "fundamentals of woodworking" class taught by Marc Adams at the Indianapolis woodworking show a few years ago, I was most impressed with his simple yet effective method of sharpening woodworking chisels. I contacted Marc and asked him for permission to write an article for BT3Central on how to sharpen chisels using his method. As expected, Marc was very receptive to the idea of sharing one of his "secrets". His exact response to me was " Absolutely, please feel free to teach anything you learned from me." So let's dive right into this and sharpen some chisels.
    ...
    04-29-2015, 10:15 AM
  • Primer on air fittings for the woodshop
    by LCHIEN
    Most common places to use air fittings in a home shop:
    Air compressor to hose or female QD fitting
    QD female fitting or male stud to hose
    male stud to tool (such as - air nozzle, nailer, screwdriver/drill/impact driver etc, spray painter)
    any semi-permanent 1/4" NPT to 1/4" NPT fitting

    To add to the confusion, there's nothing on a 1/4" NPT that really measures 1/4". THe threads are visibly tapered and the overall outside size of the male NPT...
    04-29-2015, 10:14 AM
  • How to use Digital Calipers for Woodworking
    by LCHIEN
    Digital calipers like these are available for 10-30 dollars. The size quoted as in "6-inch digital calipers" refers to the maximum measurement. The resolution and accuracy of these are typically .001 or one-thousandth of an inch. Some have an additional digit that shows 0 or 5 for half a thousandth. I recommend the six-inch Harbor freight ones, they work very well and are of surprisingly high quality. The stainless body ones are better than the composite plastic body ones although the plastic ones ...
    04-29-2015, 10:13 AM

The SawdustZone Statistics

Collapse

Topics: 61,269   Posts: 558,427   Members: 20,614   Active Members: 74
Welcome to our newest member, Havoily.

What's Going On

Collapse

There are currently 10019 users online. 3 members and 10016 guests.

Most users ever online was 11,343 at 11:05 AM on Today.

Working...