X
Collapse
-
Ryobi BTS-21 10" Table Saw Long Term review.
Not years since purchase, but 10 months of fairly active use, I can honestly say I have a good feel for what the BTS-21 can, and cannot do well. So let's get down to business.
The good.
#1. Folding stand with wheels makes getting this thing out of the way a breeze.
#2. Outfeed Extension works well for intermediate size pieces, needs more for large pieces.
#3. Sliding Miter table makes miter cuts fast, accurate, and easy.
#4. Built in dust collection shroud around blade in housing makes connecting to a shop vac dust collector easy.
#5. Sturdy, accurate fence locks front and rear rails and holds on tight.
#6. Cord wrap keeps the cord out of the way when not in use.
#7. On board tool / accessory storage. This saw has nice slots for the fence, miter fence, extra blades, and blade wrenches.
#8. Generous 27" rip capacity.
#9. Reasonably good stock general purpose blade.
#10. Light enough weight to make loading and unloading into a truck easy.
#11. Alignments stable through lots of knocking around and moving.
#12. Very accurate cuts. As long as the operator doesn't screw up that is... I recently ripped 2x4 lumber, 8 feet in length to 1.25" square (2 pieces) for a mobile base project, and my stock ended up 1.25" the entire length. This requires a steady hand though, it is really easy to kick the stock sideways and get the balde bound up.
The bad.
#1. Complete lack of a miter slot, or ability to easily add a miter slot.
#2. Lack of ability to add extension rails or other accessories like the BT3x00 series has to offer.
#3. Open housing bottom, back, combined with the guard design make for relatively poor dust collection. Better than most in this category of saw, but still pretty lousy.
#4. Far fewer expansion options compared to the BT3x00 series.
#5. Direct drive not as smooth as belt drive.
#6. Arbor limits the dado stack that can be used to 5/8".
For the type of saw this is, it has been amazingly accurate, keeps its settings, and puts up with being tossed in the back of a truck and hauled around to job sites. I have used my saw as my shop table saw, as well as hauled it around to a couple of friend's homes to make quick work of ripping and cross cutting a variety of materials for siding and deck projects.
If you absolutely have to have a new table saw, portability is important, and your budget is under $250.00, you will want to wait for this saw to go on sale. It is a good little saw. But it has its limitations. I would consider the Ryboi BT3100 to be a superior saw in nearly all regards except for portability. If portability and new aren't important, find a lovingly used BT and be happy with it...Posting comments is disabled.
Categories
Collapse
Article Tags
Collapse
- box joint (1)
- BT3x00 (71)
- bt3000 (5)
- bt3100 (2)
- diy (2)
- dust collection (11)
- Enhancements & Modifications (5)
- Fence Attachments (12)
- General (5)
- Hand Tool Accessories (3)
- Hand Tools (14)
- Measuring & Layout (6)
- miter fence (3)
- Mobile BT3x00 (9)
- Mobile Tools (9)
- Other Reviews (4)
- Other Tools (5)
- Power Tool Accessories (28)
- Power Tools (75)
- rails (3)
- rip fence (5)
- safety (5)
- Sharpening (4)
- t-nut (3)
- wide table kit (2)
Latest Articles
Collapse
-
by twistsol
Summary
I built my miter station last summer and used the Kreg Precision Trak & Stop Kit. The kit was just the starting point. 8 feet of track and a single flip stop didn’t meet my needs since I was building a miter station the width of my shop, nearly 24 feet. I added four 48” pieces of top track and three additional swing stops so I could have two left and two right. Finally, I added metric rules to the top. Total cost breakdown is as follows
...-
Channel: Tool Reviews
03-23-2022, 02:59 PM -
-
by LCHIENI have always had trouble mounting small hardware on small wood boxes, with the hasps and hinges always looking slightly off perfectly square - particularly a problem with flat head screws and countersunk hardware which aligns the hardware to the hole location and centers on the hole.
I'm talking small wood screws. I place and mark the hardware carefully and mark the center of the hole with a sharp awl.
The problem comes about with small bits like 1/16 and 5/64 and 3/32"...-
Channel: Tool Reviews
08-30-2021, 12:18 AM -
-
by twistsolSince my new shop is in the basement, dust collection is a bit more important than when I had my own building and could do as I pleased in the shop. With that in mind, I upgraded the dust collection on my table saw. I purchased the Grizzly Overarm Blade Guard to use with the saw.
First impressions were that this is an extremely solid and well built unit. It's made mostly of steel and connects to a 4" DC hose. There were a number of issues getting it set up and installed, and a...-
Channel: Tool Reviews
07-26-2021, 03:47 PM -
-
by twistsol
I decided to look for the rock bottom cheapest 32mm drilling system available that would let let me create real 5mm holes spaced 32mm apart, that was easy to use, and didn’t require a bunch of setup time. I’m really surprised at how much I like this little Keg jig especially when you consider the price of $34.99, and it has everything included. There were a couple of jigs cheaper but you needed to buy a self-centering 5mm bit to go along with them so they would...-
Channel: Tool Reviews
03-19-2021, 05:57 PM -
-
by LCHIENHere's a tool I found useful for marking. Accutrax pencil blade marking knife.
I have one I've been using on and off for a while. Its a fine pencil lead in the shape of a utility blade that can be installed in any utility knife handle and used with a straight edge, combination square, saddle square etc. to mark easily seen, fine lines on wood..
Here's mine. I have not broken it, it seems to be quite sturdy. The sharp edge lasts a long time. I'm still on the...-
Channel: Tool Reviews
01-14-2021, 03:25 AM -
-
by LCHIENHey, I'm sharing one of my favorite tools. A Veritas Saddle Square. Actually I have two in different sizes. This is the large size for marking 2x4 and 4x4 (shown on 4x4 here). One of those tools that makes woodworking a pleasure.
They're great for continuing lines from side to side. And even side to opposite side.
Works really well when the board has a rounded edge or some wane where the edge is not really sharp and square but the two adjacent faces are square to...-
Channel: Tool Reviews
01-13-2021, 02:20 AM -
The SawdustZone Statistics
Collapse
Topics: 61,301
Posts: 558,646
Members: 20,640
Active Members: 68
Welcome to our newest member, Poolwaterpro.
What's Going On
Collapse
There are currently 7460 users online. 3 members and 7457 guests.
Most users ever online was 15,771 at 02:28 PM on 04-26-2024.
Footer Ad
Collapse
First impression:
When I unfolded this thing, I was first impressed by the stability of the legs. The one in the store was wobbly, because it was missing the adjustable foot. After researching this saw, I learned that many people are happy with the stability, and so am I. I am a little nervous about the little adjustable foot. It works really well now, but I can see it breaking if you are not careful.
Out of the box, it's pretty accurate. I checked everything with a framing square only, and I am getting quite accurate cuts.
The extendable outfeed support is nice. When ripping 8 ft. 2x material, I needed no addition support. I did however use a saw horse when I ripped a 4x4.
I'm not sure about this SMT. I cannot eye-ball it and get a good 90 degree angle. The cross cutting that I've done, I've used a framing square to get accurate cuts.
Things I've cut:
Ripped 8' pine 2x4's very accurately. I ripped them in half and ripped them in 1" strips.
Made a bunch of push sticks out of 1x material
Ripped a bunch of OSB into 24" and 16" wide pieces. It's only 7/16" OSB, but it did handle 4x8 sheet goods with good stability. I never felt like it was going to tip.
Cross cut 8' by 16" OSB with support on both sides. I cross cut a 4' piece with no support.
Ripped and 8' PT pine 4x4. I could tell that this was taxing the motor slightly. All I did was slow my feed rate, and it did fine.
I know all of the cuts I've talked about are basically framing/rough carpentry cuts, but I wanted to start this as soon as I got the saw and keep it updated.
So far, I am very pleased with the saw. I really like the mobility since I do most of my work in the driveway. I will update this as I get more projects under my belt.