Knife marking pencil Accutrax

Collapse
X
Collapse
  •  

  • Knife marking pencil Accutrax

    Here's a tool I found useful for marking. Accutrax pencil blade marking knife.

    Click image for larger version  Name:	accutrax.JPG Views:	0 Size:	69.1 KB ID:	842124

    I have one I've been using on and off for a while. Its a fine pencil lead in the shape of a utility blade that can be installed in any utility knife handle and used with a straight edge, combination square, saddle square etc. to mark easily seen, fine lines on wood..

    Here's mine. I have not broken it, it seems to be quite sturdy. The sharp edge lasts a long time. I'm still on the original blade and it came with a pack of 5 and like utility blades, can be reversed when too worn. Being in a knife handle, its perfect to mark with just as you'd cut a piece of paper or cardboard.
    Never needs sharpening, extend it as it wears with the blade retractor of the knife handle. Much sturdier than a mechanical pencil lead for marking on rough or uneven wood.
    Click image for larger version  Name:	P1140026.JPG Views:	0 Size:	138.5 KB ID:	842125
    Last edited by LCHIEN; 01-14-2021, 11:51 AM.

    • twistsol
      #1
      twistsol commented
      Editing a comment
      I tried those a few years ago when McFeely's included a 3 pack in an order as a bonus. I'm too ham fisted for them and broke all three within a few days. Your mileage may very if you're normal. I keep .5mm mechanical pencils in the shop when I need to make fine pencil lines but usually use my left handed marking knife.

    • LCHIEN
      #2
      LCHIEN commented
      Editing a comment
      Update 2/11/2024 - I looked on line, Woodpeckers still carries these. https://www.woodpeck.com/measuring/p...82&price=10-20
      Lee Valley shows not available
      Acme tools https://www.acmetools.com/accutrax-p...944098628.html
    Posting comments is disabled.

Latest Articles

Collapse

  • A review of the Kreg Precision Trak & Stop Kit
    by twistsol

    Summary
    I built my miter station last summer and used the Kreg Precision Trak & Stop Kit. The kit was just the starting point. 8 feet of track and a single flip stop didn’t meet my needs since I was building a miter station the width of my shop, nearly 24 feet. I added four 48” pieces of top track and three additional swing stops so I could have two left and two right. Finally, I added metric rules to the top. Total cost breakdown is as follows
    ...
    03-23-2022, 02:59 PM
  • Review of VIX-type Self Centering drill bits
    by LCHIEN
    I have always had trouble mounting small hardware on small wood boxes, with the hasps and hinges always looking slightly off perfectly square - particularly a problem with flat head screws and countersunk hardware which aligns the hardware to the hole location and centers on the hole.

    I'm talking small wood screws. I place and mark the hardware carefully and mark the center of the hole with a sharp awl.
    The problem comes about with small bits like 1/16 and 5/64 and 3/32"...
    08-30-2021, 12:18 AM
  • Grizzly Overarm Blade Guard review.
    by twistsol
    Since my new shop is in the basement, dust collection is a bit more important than when I had my own building and could do as I pleased in the shop. With that in mind, I upgraded the dust collection on my table saw. I purchased the Grizzly Overarm Blade Guard to use with the saw.

    First impressions were that this is an extremely solid and well built unit. It's made mostly of steel and connects to a 4" DC hose. There were a number of issues getting it set up and installed, and a...
    07-26-2021, 03:47 PM
  • Kreg KMA 3220 5mm Shelf Pin Jig
    by twistsol



    I decided to look for the rock bottom cheapest 32mm drilling system available that would let let me create real 5mm holes spaced 32mm apart, that was easy to use, and didn’t require a bunch of setup time. I’m really surprised at how much I like this little Keg jig especially when you consider the price of $34.99, and it has everything included. There were a couple of jigs cheaper but you needed to buy a self-centering 5mm bit to go along with them so they would...
    03-19-2021, 05:57 PM
  • Knife marking pencil Accutrax
    by LCHIEN
    Here's a tool I found useful for marking. Accutrax pencil blade marking knife.



    I have one I've been using on and off for a while. Its a fine pencil lead in the shape of a utility blade that can be installed in any utility knife handle and used with a straight edge, combination square, saddle square etc. to mark easily seen, fine lines on wood..

    Here's mine. I have not broken it, it seems to be quite sturdy. The sharp edge lasts a long time. I'm still on the...
    01-14-2021, 03:25 AM
  • Saddle squares
    by LCHIEN
    Hey, I'm sharing one of my favorite tools. A Veritas Saddle Square. Actually I have two in different sizes. This is the large size for marking 2x4 and 4x4 (shown on 4x4 here). One of those tools that makes woodworking a pleasure.



    They're great for continuing lines from side to side. And even side to opposite side.
    Works really well when the board has a rounded edge or some wane where the edge is not really sharp and square but the two adjacent faces are square to...
    01-13-2021, 02:20 AM

The SawdustZone Statistics

Collapse

Topics: 61,269   Posts: 558,427   Members: 20,614   Active Members: 74
Welcome to our newest member, Havoily.

What's Going On

Collapse

There are currently 9914 users online. 6 members and 9908 guests.

Most users ever online was 11,343 at 11:05 AM on Today.

Working...