X
Collapse
-
Snap On Blue Point AP 500 dual hammer impact wrench.
The Snap On / Blue Point AT500C short snout 1/2" dual hammer impact wrench came into my possesion directly off of the Snap On Truck back in 1991 when I was a working mechanic. This impact wrench replaced my initial Craftsman single hammer model. The adjustable torque was well able to break loose anything my half inch impact sockets were willing to take, yet had enough finesse that it has actually been useful for utility woodworking projects such as driving lag bolts into hardwoods.
For the home woodworker that occasionally spins a wrench, and needs an impact wrench to drive long lag bolts, and help remove that transmission out of the old Jeep, Barracuda, or whatever project car... Well the AT500C is most likely not money well spent. While this is a TOP NOTCH impact wrench, the support and coverage from Snap On is just not needed by the hobbyist. Not to mention most guys aren't on the Snap On dealer's route...
So spend your money in better areas, grab an Ingersoll Rand with similar specs, and spend the extra money on some band saw blades...Posting comments is disabled.
Categories
Collapse
Article Tags
Collapse
- BT3x00 (71)
- bt3000 (5)
- bt3100 (2)
- diy (2)
- dust collection (11)
- Enhancements & Modifications (5)
- Fence Attachments (12)
- General (5)
- Hand Tool Accessories (3)
- Hand Tools (14)
- Measuring & Layout (6)
- miter fence (3)
- Mobile BT3x00 (9)
- Mobile Tools (9)
- Other Reviews (4)
- Other Tools (5)
- Power Tool Accessories (28)
- Power Tools (75)
- rails (3)
- rip fence (5)
- router table (1)
- safety (5)
- Sharpening (4)
- t-nut (3)
- wide table kit (2)
Latest Articles
Collapse
-
by twistsol
Summary
I built my miter station last summer and used the Kreg Precision Trak & Stop Kit. The kit was just the starting point. 8 feet of track and a single flip stop didn’t meet my needs since I was building a miter station the width of my shop, nearly 24 feet. I added four 48” pieces of top track and three additional swing stops so I could have two left and two right. Finally, I added metric rules to the top. Total cost breakdown is as follows
...-
Channel: Tool Reviews
03-23-2022, 02:59 PM -
-
by LCHIENI have always had trouble mounting small hardware on small wood boxes, with the hasps and hinges always looking slightly off perfectly square - particularly a problem with flat head screws and countersunk hardware which aligns the hardware to the hole location and centers on the hole.
I'm talking small wood screws. I place and mark the hardware carefully and mark the center of the hole with a sharp awl.
The problem comes about with small bits like 1/16 and 5/64 and 3/32"...-
Channel: Tool Reviews
08-30-2021, 12:18 AM -
-
by twistsolSince my new shop is in the basement, dust collection is a bit more important than when I had my own building and could do as I pleased in the shop. With that in mind, I upgraded the dust collection on my table saw. I purchased the Grizzly Overarm Blade Guard to use with the saw.
First impressions were that this is an extremely solid and well built unit. It's made mostly of steel and connects to a 4" DC hose. There were a number of issues getting it set up and installed, and a...-
Channel: Tool Reviews
07-26-2021, 03:47 PM -
-
by twistsol
I decided to look for the rock bottom cheapest 32mm drilling system available that would let let me create real 5mm holes spaced 32mm apart, that was easy to use, and didn’t require a bunch of setup time. I’m really surprised at how much I like this little Keg jig especially when you consider the price of $34.99, and it has everything included. There were a couple of jigs cheaper but you needed to buy a self-centering 5mm bit to go along with them so they would...-
Channel: Tool Reviews
03-19-2021, 05:57 PM -
-
by LCHIENHere's a tool I found useful for marking. Accutrax pencil blade marking knife.
I have one I've been using on and off for a while. Its a fine pencil lead in the shape of a utility blade that can be installed in any utility knife handle and used with a straight edge, combination square, saddle square etc. to mark easily seen, fine lines on wood..
Here's mine. I have not broken it, it seems to be quite sturdy. The sharp edge lasts a long time. I'm still on the...-
Channel: Tool Reviews
01-14-2021, 03:25 AM -
-
by LCHIENHey, I'm sharing one of my favorite tools. A Veritas Saddle Square. Actually I have two in different sizes. This is the large size for marking 2x4 and 4x4 (shown on 4x4 here). One of those tools that makes woodworking a pleasure.
They're great for continuing lines from side to side. And even side to opposite side.
Works really well when the board has a rounded edge or some wane where the edge is not really sharp and square but the two adjacent faces are square to...-
Channel: Tool Reviews
01-13-2021, 02:20 AM -
The SawdustZone Statistics
Collapse
Topics: 61,301
Posts: 558,646
Members: 20,641
Active Members: 68
Welcome to our newest member, Poolwaterpro.
What's Going On
Collapse
There are currently 4380 users online. 2 members and 4378 guests.
Most users ever online was 15,771 at 02:28 PM on 04-26-2024.
Footer Ad
Collapse