DIY BT3x Wooden Miter Fence Holder - Rod Kirby original design

Collapse
X
Collapse
  •  

  • DIY BT3x Wooden Miter Fence Holder - Rod Kirby original design

    Somewhere along the past I documented the Rod Kirby Shop Built (DIY) Miter Fence Holder

    Click image for larger version Name: PB232281.jpg Views: 1 Size: 46.1 KB ID: 862240 Click image for larger version Name: PB232272.jpg Views: 1 Size: 61.8 KB ID: 862241 Click image for larger version Name: PB232278.jpg Views: 1 Size: 46.7 KB ID: 862242 Click image for larger version Name: PB232282.jpg Views: 1 Size: 55.5 KB ID: 862243 Click image for larger version Name: PB232273.jpg Views: 1 Size: 51.0 KB ID: 862245

    Click image for larger version Name: image.png Views: 1 Size: 596.7 KB ID: 862246

    CCF-KIRBY MITER FENCE HOLDER DETAIL.pdf

    The above PDF can be downloaded and has the measurements for the holder parts - its rather simple,
    Really takes a top plate, a block and a compound T-slot strip, plus you need a 5/16-18 x 3" bolt and a 5/16-18 female threaded knob the latter two can be bought most hardware stores.

    I'm pretty sure you can hew the pieces for this out of a short piece of 2x4 using your BT3000.
    Attached Files
    Tags: None
      • LCHIEN
        #1
        LCHIEN commented
        04-12-2026, 07:04 PM
        Editing a comment
        for some reason I found this in the non-published limbo. I think it may duplicate something out there but I hit publish anyway.
        Posting comments is disabled.

      Latest Articles

      Collapse
      • DIY BT3x Wooden Miter Fence Holder - Rod Kirby original design
        by LCHIEN
        Somewhere along the past I documented the Rod Kirby Shop Built (DIY) Miter Fence Holder





        CCF-KIRBY MITER FENCE HOLDER DETAIL.pdf

        The above PDF can be downloaded and has the measurements for the holder parts - its rather simple,
        Really takes a top plate, a block and a compound T-slot strip, plus you need a 5/16-18 x 3" bolt and a 5/16-18 female threaded knob the latter two can be bought most hardware stores.

        I'm pretty...
        11-30-2025, 02:24 AM
      • Small T-Nut for the Left side of Rip Fence and Front of Miter Fence on BT3x saws.
        by LCHIEN
        Small T-nut for the left side of BT3 rip fence or front of miter fence (Article Version)

        11-30-2023, 04:00 PM
        I have found a perfect T-nut for the front of the BT3 miter fence and for the left side of the rip fence (same extrusion used both places)

        Its actually a weld nut, but fits the T-slot described above.

        Weld Nut: #10-24 Thread, Tab, 1/32 in Base Ht, 3/8 in Base Wd, 5/8 in Base Lg, Steel, 50 PK
        Item 1LAJ3 Mfr. Model 1LAJ3​ (WW Graingers)...
        12-06-2023, 10:19 PM
      • Special DIY T-bolt for BT3000 Miter Fence, Rip Fence and Rails
        by LCHIEN
        After a bit more thinking, some universal T-bolts for the rip miter fence make more sense than fixture blocks.
        The two big slots in the rip fence and the miter fence and the front and rear rails are sized to take 1.00 inches wide x 1/8th and 1-1/8" wide x 1/8th.

        So I took some 1/8th flat Aluminum 1.00 inches wide and cut 1-1/8" long to make a 1" x 1-1/8" rectangular plates; I used a short rip fence Block to space the length but not cause a kickback with the...
        07-09-2023, 01:37 PM
      • How to make a BT3x00 Rip Fence/Miter Fence fixture block for mounting jigs
        by LCHIEN

        DIY BT3000 FIXTURE BLOCK for Rip/Miter Fence extrusion

        Simple shop construction - no machining.

        This is intended to fit the top T-track on the Rip and miter fence (uses the same extrusion) on the Ryobi BT3x00 / Craftsman 22811 family of saws
        You must make the Block and Base parts; you can make them 1.5" or 3 inches long or modify to any other length.
        Make the base from 1/8” aluminum bar, you can get 1.5”, 2”, and 3” at Lowes...
        05-24-2023, 08:55 PM
      • Another Thin Strip Jig
        by twistsol
        Ripping thin strips can be accomplished in a number of ways, but this jig is the best I've found so far.

        ​
        • There is no need to move the fence so every strip comes out exactly the same.
        • It is incredibly easy to build
        • It keeps your hands well away from the blade the whole time
        • It keeps control of the strip you are ripping all the way through the cut and past the blade
        • It doesn't interfere with the blade guard.
        • You can cut strips from any length of stock
        In the starting position,...
        04-16-2023, 09:42 AM
      • BT3000/BT3100 tall rip fence simple using fence clamps
        by LCHIEN
        BT3000 tall rip fence

        09-12-2021, 07:58 PM
        I have had a tall BT3000 fence for a number of years, I should have used it a few days ago but I didn't because it was too much trouble, And I paid the price as the tall item was a little unstable and I had a hard time controlling it as the two pieces separated and wallowed out a bigger kerf than I wanted at one place.

        Anyway the BT3000 tall fence is generally held on by the T-slots in the side of the rip fence. This is...
        10-20-2021, 02:27 AM
      View All

      The SawdustZone Statistics

      Collapse
      Topics: 61,701   Posts: 561,434   Members: 20,814   Active Members: 21
      Welcome to our newest member, adambsullivan.

      What's Going On

      Collapse

      There are currently 1830 users online. 1 members and 1829 guests.

      Most users ever online was 71,993 at 12:49 PM on 01-13-2026.

      Footer Ad

      Collapse
      Working...