Another Thin Strip Jig

Collapse
X
Collapse
  •  

  • Another Thin Strip Jig

    Ripping thin strips can be accomplished in a number of ways, but this jig is the best I've found so far.

    Click image for larger version

Name:	IMG_3045.jpg
Views:	2345
Size:	66.3 KB
ID:	854850
    • There is no need to move the fence so every strip comes out exactly the same.
    • It is incredibly easy to build
    • It keeps your hands well away from the blade the whole time
    • It keeps control of the strip you are ripping all the way through the cut and past the blade
    • It doesn't interfere with the blade guard.
    • You can cut strips from any length of stock
    In the starting position, the flag stop holds the jog in place as you push the stock through the blade. The stock slides along the MDF as a fence and slips under the cutout in the flag stop

    Click image for larger version

Name:	IMG_3048.jpg
Views:	160
Size:	69.6 KB
ID:	854851

    Once you the end of the stock clears the flag stop, rotate it down and the tab sticking out controls the strip through the rest of the cut and pushes it past the blade.

    Click image for larger version

Name:	IMG_3049.jpg
Views:	195
Size:	111.1 KB
ID:	854852

    I made the jig 200mm wide so when I need a 5mm strip, I set my fence to 205 mm and I'm ready to go. I found this jig on youtube and made it from scraps in the shop, plus a leftover knob.





    • LCHIEN
      #1
      LCHIEN commented
      Editing a comment
      Yeah, that looks like a good jig, makes a lot of sense. I will make one next time I need a number of thin rips!
    Posting comments is disabled.

Latest Articles

Collapse

  • Small T-Nut for the Left side of Rip Fence and Front of Miter Fence on BT3x saws.
    by LCHIEN
    Small T-nut for the left side of BT3 rip fence or front of miter fence (Article Version)

    11-30-2023, 04:00 PM
    I have found a perfect T-nut for the front of the BT3 miter fence and for the left side of the rip fence (same extrusion used both places)

    Its actually a weld nut, but fits the T-slot described above.

    Weld Nut: #10-24 Thread, Tab, 1/32 in Base Ht, 3/8 in Base Wd, 5/8 in Base Lg, Steel, 50 PK
    Item 1LAJ3 Mfr. Model 1LAJ3​ (WW Graingers)...
    12-07-2023, 12:19 AM
  • Special DIY T-bolt for BT3000 Miter Fence, Rip Fence and Rails
    by LCHIEN
    After a bit more thinking, some universal T-bolts for the rip miter fence make more sense than fixture blocks.
    The two big slots in the rip fence and the miter fence and the front and rear rails are sized to take 1.00 inches wide x 1/8th and 1-1/8" wide x 1/8th.

    So I took some 1/8th flat Aluminum 1.00 inches wide and cut 1-1/8" long to make a 1" x 1-1/8" rectangular plates; I used a short rip fence Block to space the length but not cause a kickback with the...
    07-09-2023, 02:37 PM
  • How to make a BT3x00 Rip Fence/Miter Fence fixture block for mounting jigs
    by LCHIEN

    DIY BT3000 FIXTURE BLOCK for Rip/Miter Fence extrusion

    Simple shop construction - no machining.


    This is intended to fit the top T-track on the Rip and miter fence (uses the same extrusion) on the Ryobi BT3x00 / Craftsman 22811 family of saws
    You must make the Block and Base parts; you can make them 1.5" or 3 inches long or modify to any other length.
    Make the base from 1/8” aluminum bar, you can get 1.5”, 2”, and 3” at Lowes...
    05-24-2023, 09:55 PM
  • Another Thin Strip Jig
    by twistsol
    Ripping thin strips can be accomplished in a number of ways, but this jig is the best I've found so far.

    • There is no need to move the fence so every strip comes out exactly the same.
    • It is incredibly easy to build
    • It keeps your hands well away from the blade the whole time
    • It keeps control of the strip you are ripping all the way through the cut and past the blade
    • It doesn't interfere with the blade guard.
    • You can cut strips from any length of stock
    In the starting position,...
    04-16-2023, 10:42 AM
  • BT3000/BT3100 tall rip fence simple using fence clamps
    by LCHIEN
    BT3000 tall rip fence

    09-12-2021, 07:58 PM
    I have had a tall BT3000 fence for a number of years, I should have used it a few days ago but I didn't because it was too much trouble, And I paid the price as the tall item was a little unstable and I had a hard time controlling it as the two pieces separated and wallowed out a bigger kerf than I wanted at one place.

    Anyway the BT3000 tall fence is generally held on by the T-slots in the side of the rip fence. This is...
    10-20-2021, 03:27 AM
  • Extending rails/rail profiles
    by LCHIEN


    I am finally going to use my BT3000 extension rails.
    My objective is to have some easily attachable rail extensions rather than a full time wide BT3000 using two full rails taking up a lot of space and requiring table support under the right side as many do.
    I just want some wider support but not to do full 4x8 sheets of ply... if I need that, I'll break the sheet down on some sawhorses with a circ saw and some guides.

    I think I am going to cut my extension...
    08-14-2021, 11:32 AM

The SawdustZone Statistics

Collapse

Topics: 61,269   Posts: 558,427   Members: 20,614   Active Members: 74
Welcome to our newest member, Havoily.

What's Going On

Collapse

There are currently 11483 users online. 0 members and 11483 guests.

Most users ever online was 11,606 at 02:28 AM on Today.

Working...