BT3000 Jig Saw Mount

Collapse
X
Collapse
  •  

  • BT3000 Jig Saw Mount

    BT3000 Jig Saw Mount Designed by Jim Frye

    This setup uses an old Jig Saw and a 3/4” thick plywood router mounting plate. The mounting plate is cut and relieved to hold the base of the jig saw against the underside of the BT3K accessory table. Since this was a spare jigsaw, it is permanently mounted in the plate with adhesive. Different saws will require different cutting and relieving and could conceivably be mounted with screws and nuts to facilitate removal from the plate. Thus, there are no drawings with this file, just some pictures to show the finished product. I used a curved sink tail pipe screwed to the mounting plate to provide a shop vac hose connection point. I used masking tape to enclose the space between the saw and the pipe to further enhance the dust pickup. Note the steel washers epoxied to the mounting plate to provide crush protection when the jig is bolted to the BT3K table.

    Original PDF Document:
    jigsawins.pdf

    BT3000 Jig Saw Mount Designed by Jim Frye 01

    BT3000 Jig Saw Mount Designed by Jim Frye 02

    BT3000 Jig Saw Mount Designed by Jim Frye 03
    Tags: BT3x00
        Posting comments is disabled.

      Latest Articles

      Collapse
      • Small T-Nut for the Left side of Rip Fence and Front of Miter Fence on BT3x saws.
        by LCHIEN
        Small T-nut for the left side of BT3 rip fence or front of miter fence (Article Version)

        11-30-2023, 04:00 PM
        I have found a perfect T-nut for the front of the BT3 miter fence and for the left side of the rip fence (same extrusion used both places)

        Its actually a weld nut, but fits the T-slot described above.

        Weld Nut: #10-24 Thread, Tab, 1/32 in Base Ht, 3/8 in Base Wd, 5/8 in Base Lg, Steel, 50 PK
        Item 1LAJ3 Mfr. Model 1LAJ3​ (WW Graingers)...
        12-06-2023, 11:19 PM
      • Special DIY T-bolt for BT3000 Miter Fence, Rip Fence and Rails
        by LCHIEN
        After a bit more thinking, some universal T-bolts for the rip miter fence make more sense than fixture blocks.
        The two big slots in the rip fence and the miter fence and the front and rear rails are sized to take 1.00 inches wide x 1/8th and 1-1/8" wide x 1/8th.

        So I took some 1/8th flat Aluminum 1.00 inches wide and cut 1-1/8" long to make a 1" x 1-1/8" rectangular plates; I used a short rip fence Block to space the length but not cause a kickback with the...
        07-09-2023, 02:37 PM
      • How to make a BT3x00 Rip Fence/Miter Fence fixture block for mounting jigs
        by LCHIEN

        DIY BT3000 FIXTURE BLOCK for Rip/Miter Fence extrusion

        Simple shop construction - no machining.

        This is intended to fit the top T-track on the Rip and miter fence (uses the same extrusion) on the Ryobi BT3x00 / Craftsman 22811 family of saws
        You must make the Block and Base parts; you can make them 1.5" or 3 inches long or modify to any other length.
        Make the base from 1/8” aluminum bar, you can get 1.5”, 2”, and 3” at Lowes...
        05-24-2023, 09:55 PM
      • Another Thin Strip Jig
        by twistsol
        Ripping thin strips can be accomplished in a number of ways, but this jig is the best I've found so far.

        ​
        • There is no need to move the fence so every strip comes out exactly the same.
        • It is incredibly easy to build
        • It keeps your hands well away from the blade the whole time
        • It keeps control of the strip you are ripping all the way through the cut and past the blade
        • It doesn't interfere with the blade guard.
        • You can cut strips from any length of stock
        In the starting position,...
        04-16-2023, 10:42 AM
      • BT3000/BT3100 tall rip fence simple using fence clamps
        by LCHIEN
        BT3000 tall rip fence

        09-12-2021, 07:58 PM
        I have had a tall BT3000 fence for a number of years, I should have used it a few days ago but I didn't because it was too much trouble, And I paid the price as the tall item was a little unstable and I had a hard time controlling it as the two pieces separated and wallowed out a bigger kerf than I wanted at one place.

        Anyway the BT3000 tall fence is generally held on by the T-slots in the side of the rip fence. This is...
        10-20-2021, 03:27 AM
      • Extending rails/rail profiles
        by LCHIEN


        I am finally going to use my BT3000 extension rails.
        My objective is to have some easily attachable rail extensions rather than a full time wide BT3000 using two full rails taking up a lot of space and requiring table support under the right side as many do.
        I just want some wider support but not to do full 4x8 sheets of ply... if I need that, I'll break the sheet down on some sawhorses with a circ saw and some guides.

        I think I am going to cut my extension...
        08-14-2021, 11:32 AM
      View All

      The SawdustZone Statistics

      Collapse
      Topics: 61,473   Posts: 559,867   Members: 20,749   Active Members: 34
      Welcome to our newest member, avrorafrix.

      What's Going On

      Collapse

      There are currently 2640 users online. 1 members and 2639 guests.

      Most users ever online was 29,192 at 02:53 AM on 06-10-2024.

      Footer Ad

      Collapse
      Working...

      We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.

      By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.

      I Agree