X
Collapse
-
BT3000/BT3100 Belly pan easy dust collection
I made a belly pan dust collection for my BT3000, using a commercially available, cheap dust pan from one of the woodworking supply houses with a 4" hose fitting.
It seems to work effectively very simple DC belly pan under BT3000. Not tightly fitting I wanted to allow air in to carry the dust to the DC, pulling on a close cabinet is not a good idea. SO the plywood sits on the stand, not screwed down or anything. So there's air coming in thru the ends and the Shroud dust port arc. This is an actual picture after use, not cleaned up. The DC is connected with two 4-inch hoses to the shroud and the belly pan. The biggest issue is if I don't use a zctp the thin long cutoffs get sucked in and end up in the Shroud hose jamming it up.
The BT3000 end panel is removed for photographic illustration; I just set the plywood setting on the bottom flanges of the saw after cutting an opening in the plywood and fastening the plastic pan. No modifications, holes or attachments were made to the saw.
I've been using this for years.Last edited by LCHIEN; 03-16-2024, 04:41 PM.-
#1LCHIEN commented03-16-2024, 04:39 PMEditing a commentThis is a reposting, I noticed it wasn't in the articles.
-
#2Dedpedal commented03-20-2024, 10:03 AMEditing a commentI did one similar.
Posting comments is disabled. -
Categories
Collapse
Article Tags
Collapse
- BT3x00 (71)
- bt3000 (5)
- bt3100 (2)
- diy (2)
- dust collection (11)
- Enhancements & Modifications (5)
- Fence Attachments (12)
- General (5)
- Hand Tool Accessories (3)
- Hand Tools (14)
- Measuring & Layout (6)
- miter fence (3)
- Mobile BT3x00 (9)
- Mobile Tools (9)
- Other Reviews (4)
- Other Tools (5)
- Power Tool Accessories (28)
- Power Tools (75)
- rails (3)
- rip fence (5)
- safety (5)
- Sharpening (4)
- t-nut (3)
- transfer punch (1)
- wide table kit (2)
Latest Articles
Collapse
-
by LCHIENTrying to drill into a outside 90 degree corner, 45° to each side, is tough, the drill bit keeps wanting to walk off.
You can whack a small flat on the corner.
But here is a way I did it perfectly. Using this corner drill jig
Using the drilling jig, One hand is enough to hold the jig while drilling. The small board touching the top of the jig is my measurement stick. I use that to set the precise reproducible location of the hole relative to the top of the workpiece....-
Channel: Tutorials & How To
Yesterday, 10:41 PM -
-
by LCHIENHere's how I do my Featherboard operations. As you know, Featherboards are spring boards meant to hold the workpiece against the fence snugly to ensure accurate rips while freeing both your hands for hand over hand and push stick smooth, even feeding of the workpiece to avoid burning and sawmarks.
The Feather board is the classic one that they suggest you make.... Mine was made 20+ years ago, apparently a 1x4 piece of pine wood with one end cut at 30 degrees. 15-16 inches long 3 to...-
Channel: SawdustZone Articles
04-15-2024, 06:19 PM -
-
by LCHIENI made a belly pan dust collection for my BT3000, using a commercially available, cheap dust pan from one of the woodworking supply houses with a 4" hose fitting.
It seems to work effectively very simple DC belly pan under BT3000. Not tightly fitting I wanted to allow air in to carry the dust to the DC, pulling on a close cabinet is not a good idea. SO the plywood sits on the stand, not screwed down or anything. So there's air coming in thru the ends and the Shroud dust port arc....-
Channel: SawdustZone Articles
03-16-2024, 04:37 PM -
-
by LCHIEN
With the small t-nut for the front of the rip fence and miter fence, I made a new stop block that can be used on both
https://www.sawdustzone.org/articles...nce-attachment
When used on the rip fence , it can set a stop for cross cutting fixed lengths off a piece against the miter fence without risking a kickback from continuous...-
Channel: SawdustZone Articles
02-17-2024, 01:43 AM -
-
by LCHIENSmall T-nut for the left side of BT3 rip fence or front of miter fence (Article Version)
11-30-2023, 04:00 PM
I have found a perfect T-nut for the front of the BT3 miter fence and for the left side of the rip fence (same extrusion used both places)
Its actually a weld nut, but fits the T-slot described above.
Weld Nut: #10-24 Thread, Tab, 1/32 in Base Ht, 3/8 in Base Wd, 5/8 in Base Lg, Steel, 50 PK
Item 1LAJ3 Mfr. Model 1LAJ3 (WW Graingers)...-
Channel: Jigs & Fixtures
12-07-2023, 12:19 AM -
-
by LCHIENAfter a bit more thinking, some universal T-bolts for the rip miter fence make more sense than fixture blocks.
The two big slots in the rip fence and the miter fence and the front and rear rails are sized to take 1.00 inches wide x 1/8th and 1-1/8" wide x 1/8th.
So I took some 1/8th flat Aluminum 1.00 inches wide and cut 1-1/8" long to make a 1" x 1-1/8" rectangular plates; I used a short rip fence Block to space the length but not cause a kickback with the...-
Channel: Jigs & Fixtures
07-09-2023, 02:37 PM -
The SawdustZone Statistics
Collapse
Topics: 61,292
Posts: 558,610
Members: 20,637
Active Members: 70
Welcome to our newest member, cjn.
What's Going On
Collapse
There are currently 9118 users online. 0 members and 9118 guests.
Most users ever online was 15,771 at 02:28 PM on Yesterday.
Footer Ad
Collapse