Bunk bed project started - sort of

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts

  • tfischer
    replied
    Originally posted by atgcpaul
    Looks like you got through it with no incidents. A word of caution to those who might be using pics as examples, though. It's a no-no to trap the workpiece between the fence and router bit. It could make for a dangerous kickback. Think automatic ball pitcher at the batting cage with the wood being the ball.
    Hmmm, the tenoning jig seemed to be a safe way to do it - the workpiece is braced in against the back of the jig and clamped in securely.

    How else can you do it with such narrow stock? I definitely want to keep safe!
    Last edited by tfischer; 08-23-2014, 11:32 AM.

    Leave a comment:


  • atgcpaul
    replied
    Looks like you got through it with no incidents. A word of caution to those who might be using pics as examples, though. It's a no-no to trap the workpiece between the fence and router bit. It could make for a dangerous kickback. Think automatic ball pitcher at the batting cage with the wood being the ball.

    Leave a comment:


  • tfischer
    replied
    Originally posted by LCHIEN
    have you considered some 45 degree braces under some of the steps? With boys climbing on it some more lateral stiffness wouldn't hurt.
    I'll see how it feels after it dries up... with the sliding dovetails, it was really stiff even when I just dry fit it.

    Leave a comment:


  • LCHIEN
    replied
    have you considered some 45 degree braces under some of the steps? With boys climbing on it some more lateral stiffness wouldn't hurt.

    Leave a comment:


  • tfischer
    replied
    Well another weekend is here so I got some shop time in tonight. As I mentioned in the last update, my final 'major' piece of this project is the ladder. I was pretty apprehensive about this because it was the first time I've attempted anything using sliding dovetail joinery, and the angle of the ladder makes it that much more complicated (it will sit at about 10 degrees off vertical)

    Since my wife is anxious to get this done too, I talked her into helping me out - mostly as a sanity check on the math and angles involved. She was also good for moral support, and repeatedly answering "before I cut this does this seem right" lol.

    The sliding dovetails actually went shockingly smoothly once I figured it all out. I did the slots on the verticals using a standard miter gauge in my right-hand side miter slots as the SMT was too far away to be practical (My BT3 is also my router table). This worked fine. Then I used the quick and dirty tenoning jig I built earlier in the project to make the dovetails on the ladder rungs. Once I got it calibrated it worked great.

    The awesome thing about sliding dovetails is the mechanical strength involved. The picture of me holding the ladder by the bed is just a dry fit, I hadn't even cut the verticals to final length yet. After that sanity check I took it all back apart, cut them to length, rounded things over, sanded everything, then did the final glue up, which you see clamped up in the final pic.

    The end of the project is (finally) in sight! Tomorrow I plan to make the planks to support the mattress, then work on staining/finishing the remaining pieces.
    Attached Files

    Leave a comment:


  • tfischer
    replied
    Originally posted by atgcpaul
    Whoa that's a big can of stain! I was a clumsy kid. I know if I was helping my Dad, it wouldn't be too long before our driveway would have gotten a nice coat, too.
    LOL bought that can when a local Menards was clearing everything out so they could tear down the store and build bigger and newer. It's nearly gone now as we used to for a lot of new interior doors and millwork...

    Leave a comment:


  • atgcpaul
    replied
    Originally posted by capncarl
    Looks like you have plenty of help! They will remember this and tell their kids about it. One project like this we had, after the painting was done we needed to pant the garage floor to match the build.
    Whoa that's a big can of stain! I was a clumsy kid. I know if I was helping my Dad, it wouldn't be too long before our driveway would have gotten a nice coat, too.

    Leave a comment:


  • capncarl
    replied
    Looks like you have plenty of help! They will remember this and tell their kids about it. One project like this we had, after the painting was done we needed to pant the garage floor to match the build.

    Leave a comment:


  • tfischer
    replied
    Time to update this. I have the upper safety rails built now. The back one goes the whole length and just uses metal pins to connect to the headboard/footboards. I was puzzled how to get the front one, which doesn't go all the way across to allow ladder access, to be properly supported, especially since it will probably get pulled on when climbing the ladder. I ended up using 1/2" square steel as a support. I'll post pictures of how this works when I have it assembled.

    Here's a few more in-progress, although I'm a bit further than this now, I'm actually working on the ladder which is the final piece other than the slats to support the mattresses. I'm planning on using sliding dovetails on the ladder which will be a first for me. Wish me luck lol. As of this morning my BT3X is now running again (burned out a motor last Saturday). Fortunately the project was in a place where I could keep going a bit during the week without it.
    Attached Files

    Leave a comment:


  • tfischer
    replied
    Originally posted by atgcpaul
    Yep. That was my number one fear when I built my daughter's crib. Will the crib mattress fit when it's done?

    Now it's time for me to convert it from the toddler bed to the big bed and I can't find the plans to tell me how long I need to make the rails. Mattresses are fairly pliable.
    I googled mattress dimensions, and found that they jived with what my plans called for (other than the XL being 5 inches longer than a standard twin).

    I'm tall, and my boys are tall for their age, so I'm thinking the extra 5" will come in handy someday

    I also built them "junior beds" vs "toddler beds"... my son is just about to turn 10 and still in his "junior bed"! He literally goes from end to end... but it's time to get him out of there and into this one!

    Leave a comment:


  • atgcpaul
    replied
    Originally posted by tfischer
    They will take a twin XL mattress. If I measured correctly anyway
    Yep. That was my number one fear when I built my daughter's crib. Will the crib mattress fit when it's done?

    Now it's time for me to convert it from the toddler bed to the big bed and I can't find the plans to tell me how long I need to make the rails. Mattresses are fairly pliable.

    Leave a comment:


  • tfischer
    replied
    Originally posted by atgcpaul
    Looking good Tim. Maybe I missed it before. What size mattresses do those take?
    They will take a twin XL mattress. If I measured correctly anyway

    Leave a comment:


  • atgcpaul
    replied
    Looking good Tim. Maybe I missed it before. What size mattresses do those take?

    Leave a comment:


  • Pappy
    replied
    Looking great, Tim! Love the style.

    Leave a comment:


  • JimD
    replied
    Looks great. My shop garage is finally under construction. I'm looking forward to getting my tools out of storage and into my shop. Maybe in a month or two.

    Leave a comment:

Working...