Stumbled across my old thread today. I just wanted to report that 4 years later, the boys are still using these bunk beds and they have held up wonderfully. In particular the question above regarding adding stiffness to the ladders... the sliding dovetail design has held up great and it's as solid (if not more so) than a commercial ladder.
I just rebuilt the tennoning jig I whipped up quickly for this project. I made the original out of melamine-covered particle board which I had on hand but was a poor choice as the garage gets humid and it swelled up and warped slightly.. made it hard to slide on the fence and also threw off the accuracy. This time I redid it in plywood. I will try to remember to add a post to the jigs section on how it works.
Bunk bed project started - sort of
Collapse
This topic is closed.
X
X
-
I know this is an old thread, came looking for instruction to build a flat slat based bed.. did you put the detailed instructions on how you build these somewhere?Leave a comment:
-
Always wanted one just like that one when I was a kid... Looks really good!Leave a comment:
-
Thanks for the kind words. That is my hope, that they will be in use for a long, long time. Once they outgrow the bunks, you can swap the ends so that each bed has a tall headboard and a shorter footboard. I went to some lengths to make sure there wasn't an excessive amount of 'damage' done by making them bunks... when they are single beds someday there will just be a few stray holes where metal pins currently hold things together... a few wood caps bought at the hardware store and it will look like a champ. The ladder just slips over the rail (I used Rockler brackets) so no damage there, and the front upper rail bolts into threaded inserts on the inside of the rail which is will be hidden by the mattress.
And I built the as Twin-XL so they should never outgrow them. When we went mattress shopping the guy told me I must be wrong... nobody makes an XL bunk bed. I said "I do" lol.
Really had fun with this build and learned a lot.Leave a comment:
-
Beautiful work, and they look plenty strong. Those look like heirloom bunkbeds to me.Leave a comment:
-
In most cameras the normal camera orientation results in a picture file that is horizontal and the top is the top of the picture you see framed. If you hold the camera sideways then the picture file is sideways.
Many cameras nowadays have a sensor which detects gravity direction and sets some bits in the picture file indicating which way it thinks is up. THis sensor can be fooled for example by pointing it down at something like a picture on the ground... (long explanation)
Many viewer software automatically rotates the picture display according to the orientation bits, particularly the camera makers' photo viewers. However the top of the photo file is still relative to the camera itself (unless you use software to rotate it).
When you insert the file into most word processors or paint programs or forums threads they do not normally try and guess at the rotation. Physically rotating the file involves transposition: making the 2nd pixel on the first row into the 1st pixel on the second row and so on. If you had a NxM sized photo it would show up as a MxN sized photo when you are done with the transposition.
What you probably should do is to turn off display autorotation option in your viewer and then you will see the picture as it will be posted. Rotate and save the file as necessary.Last edited by LCHIEN; 09-03-2014, 12:07 AM.Leave a comment:
-
I feel for only children because they usually don't get to experience their own set of bunk beds. Great Job.
Regards BobLeave a comment:
-
Thanks all.
Sorry for the sideways pics... my camera sets the orientation properly and they look fine when I view the on the computer, but somehow uploading them here makes them rotate sideways.Leave a comment:
-
Well done! They will enjoy it!
Sent from my SCH-I545 using TapatalkLeave a comment:
-
Well, it's only taken me all summer (I got the initial wood delivery on Easter Sunday), with lots of stops and starts, but we've finally come to my final "build progress" post. We moved the beds into the boys' room today, after doing some major rearranging (we really need to do some major redecorating in there but that's another week's project).
Here are some final pics. Mattresses are on order and come tomorrow.Leave a comment:
-
Well I got a lot done on this project over the weekend... the kiddos are at my mom's until tomorrow and my original goal was to have it finished and installed in their room as a surprise when they got home. Alas, that won't happen. But I'm *so* close! Got the final coat of poly on the main parts of the bed today, and got several coats (I'm using wipe-on) on the ladder and rails. I'm thinking one final sanding and wipe-on coat on those parts and the project will be complete!
I'll be happy to have my garage back, and move on to some other projects!
We also have to buy mattresses yet... wow those are a lot spendier than I had expected for a twin XL size...Leave a comment:
-
Gotcha. I actually used that link when I was researching the joint last month... but since they were doing shelves and I was doing (much narrower) rungs it didn't seem like the fence method would work well. The tennoning jig worked extremely well, but if it's dangerous...
This would be a perfect application for one of those horizontal router tables like MCLS sells lolLast edited by tfischer; 08-23-2014, 05:11 PM.Leave a comment:
-
Typically you bury the bit in the fence, then pass the piece past the bit while it's riding on the fence-just like you'd do when routing a profile on an edge using the router table. This also exposes much less of the spinning bit in case you or something else were to fall on it.
Near the bottom of this page is what I'm describing. You back up your narrow board with something wide and square to act as your push block as well as something to ensure your profile is square to the board.
http://www.woodworkersjournal.com/Ma...ints-8965.aspxLast edited by atgcpaul; 08-23-2014, 12:43 PM.Leave a comment:

LCHIEN
Leave a comment: