Resawing for Beginners

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts

  • scorrpio
    replied
    Everything could be a problem. There essentially is a checklist of things to go over after every blade change. Stock blade on most bandsaws is lowest quality possible. Think getting a carbide-less 'plywood blade' with your TS.
    Get a quality blade, and it should improve significantly. Also, 7tpi is too fine for resawing.

    Leave a comment:


  • Greg.B
    replied
    Thanks for all your help here.

    Another item I will introduce is something I noticed late last night. And could be part of the problem. I found the blade to track close to the edge of the bottom wheel, while the top is in the middle. From this I assume that the wheels are not in the same plane, and that is probably what I should address first. I can't move the bottom wheel, but I can move the top out. I think if I move the top wheel out (towards me) then the blade would then move the opposite way on the lower wheel, toward the back of the saw. I think once I get that all lined up I should be at a better starting point.

    I am only assuming this is a problem, but I have a feeling it is.

    Leave a comment:


  • SARGE..g-47
    Guest replied
    Good morning Greg...

    As stated, the stock blade is just a show-piece. A 5/8" blade that came with what is otherwise a near flawless 118" Steel City BS is hanging on the wall ready for junk cuts if necessary.

    But my post was in reference to a statement you made about it's characteristics. Don't expect to do any efficient re-sawing with even the best blades with 7 TPI. That is a curve cutting blade and the 7 teeth will give a little better finish with less sanding. But.. with that many teeth it doesn't have the aggressiveness or deep enough gullets to remove waste that is required in sawing wide boards. You got gauranteed drift before the blade meets the stock.

    3 TPI is the ticket for re-saw. Some use 4 TPI, but even then on tall stock it won't always hack it. I will use a 4 TPI on ripping up to about 3" stock, but prefer a 3 TPI hook even for that. Since I do a combination of both, it makes more sense for me just to stay with 3 TPI.

    May I make a suggestion? Highland Woodworking www.highlandworking.com sells there Woodslicer in 1/2" and 3/4". Your saw is probably more suited for the 1/2" as the 3/4 would be pushing it. It is a thin kerf and it will get the job done with it's variable pitch. It will leave as smooth a cut as your going to get. And as Tom stated, cut a wee bit thicker so you can make a final demension as the newly opened stock will release both tension and a new door for moisture to escape.

    If you feel more comfortable with say a 3/8" blade on your saw, order a 3/8" bi-metal with 3 TPI hook. The bi-metal will last longer than the standard carbon as it can take heat that re-saw generates. The stock blade you have is probably carbon steel (cheap but OK for curve cutting). By using it for re-saw as you did, more than likely you have already over-heated it and it lost it's temper and dulled. 7 TPI combined with dis-tempered and dulling added more drift to your initial problem, IMO!

    Regards...

    Leave a comment:


  • LCHIEN
    replied
    Originally posted by Greg.B
    I'm starting to wonder how good the stock blade is. Its about .25" and 7tpi. It just won't track straight for resawing. Most of the wood comes out thinner on the top (closest to ceiling) and thicker on the bottom (closer to table). I made sure that the table and blade are @ 90 deg. I'm going to keep at it. Def. a new blade is needed. Thinking 1/2" which is the max for the saw.
    This is not a tracking issue in the sense talked about before.
    If the blade is deflecting off the vertical this will cause your problem, if you are sure that the blade was 90° to the table to begin with.
    Deflection occurs if the blade is not tensioned enough OR if the guides aren't set right top and bottom, the guide blocks should have just enough space for a dollar bill between the guide block and the blade which is about 4 mils (.004") so the ability to not be vertical is only 4 mil from vertical. Also make sure the upper guide assy is lowered right over the work. And make sure thethrust bearings are just forward of the blade and not allowing the blade to move away from between the guide blocks.

    In the middle of making your cut you might just stop the saw and see the blade is being curved or bending between the upper and lower guide blocks. and the blade is between the guide blocks.

    Leave a comment:


  • LarryG
    replied
    Originally posted by Greg.B
    I'm starting to wonder how good the stock blade is..
    Wonder no more: it's a pretty safe bet that it's cee-are-a-double-pee CRAP. The blade that came on my Grizzly G0555 was just good enough for them to be able to say, "Includes blade!" and most comments I've seen from owners of other brands indicates that this is typical.

    Tossing the stock blade in favor of a quality replacement will probably make your saw seem like a completely different tool ... that was certainly the case with mine.

    Leave a comment:


  • Greg.B
    replied
    I'm starting to wonder how good the stock blade is. Its about .25" and 7tpi. It just won't track straight for resawing. Most of the wood comes out thinner on the top (closest to ceiling) and thicker on the bottom (closer to table). I made sure that the table and blade are @ 90 deg. I'm going to keep at it. Def. a new blade is needed. Thinking 1/2" which is the max for the saw.

    Leave a comment:


  • Tom Miller
    replied
    Originally posted by Greg.B
    Follow up question. Once you resaw something do you have to thickness sand or plane ? Or should it be ready to go ? What is an acceptable range of diffference in thickness over say X inches of board ?
    I've yet to see a bandsaw finish that's even good enough for hand-sanding. I always plan to thickness sand or plane afterwards.

    Another point to consider, for anything thicker than veneer, you should expect some wood movement after resawing; either immediately in response to released tension, and/or over the course of days/weeks, due to a change in moisture content in the newly exposed face of the stock. This means you'll need to re-dimension the piece.

    Regards,
    Tom

    Leave a comment:


  • Greg.B
    replied
    Follow up question. Once you resaw something do you have to thickness sand or plane ? Or should it be ready to go ? What is an acceptable range of diffference in thickness over say X inches of board ?

    Leave a comment:


  • Greg.B
    replied
    I'm going to work on making a fence tonight. I did some re-sawing and things were on the up and up. I just have to get the fence angle closer and practive on some hardwoods.

    Leave a comment:


  • sacherjj
    replied
    While I have only resawed up to 6-1/2" tall, I have been just using Duginski's methods. If you adjust the blade forward on the top tire, the teeth of the blade go a little to the left, back they go a little to the right. I've been able to eliminate drift pretty well with that. Now, if the teeth on one side of the blade get damaged, that might cause more drift than can be corrected with this method. But with a my 3 TPI Timberwolf, so far so good.

    Leave a comment:


  • Greg.B
    replied
    Guys thats for all your input. I'm using the stock blade now and will replace shortly once I re-arrange the shop in order to fit the addition. Then I'll be able to get some serious work into it.

    Leave a comment:


  • Tom Miller
    replied
    Originally posted by JackAZ
    Basemwnt Dweller:
    "This months Fine Wood Working Magazine has an article on resawing and includes a side bar on adjusting for drift."
    I may be old and slightly blind, but I can't find such an article in my copy, which is a newstand copy. Could it be limited to the subscription copies?
    I see on-line that the article referred to is in the Jan/Feb '07 issue -- probably not on the newstands, yet, as it just showed up on-line.

    Regards,
    Tom

    Leave a comment:


  • JackAZ
    replied
    Basemwnt Dweller:
    "This months Fine Wood Working Magazine has an article on resawing and includes a side bar on adjusting for drift."
    I may be old and slightly blind, but I can't find such an article in my copy, which is a newstand copy. Could it be limited to the subscription copies?

    Leave a comment:


  • HarmsWay
    replied
    I'm with Pappy on that one. There are two schools of thought: either compensate for the drift or remove it. I think Duginski talks about it in his bandsaw book. To remove it requires a well-tensioned, good quality blade, and co-planar wheels (under that tension), which is not possible on all saws. So it's a bit more work to tune the saw initially (may require spacers to offset one wheel to get it coplanar) but makes the resawing process easier. I can just use a tall fence square on the table.

    Bob

    Leave a comment:


  • BasementDweller
    replied
    Article

    This months Fine Wood Working Magazine has an article on resawing and includes a side bar on adjusting for drift. It basicly says what you already figured out, just free hand a cut stopping half way down the test board, then back the fence up to the work piece and clamp it down. I have homemade fences for resawing and I just clamp them down.

    The most important thing I can think of is making sure you have your blade at 90 degrees to the table top. After that keep your feed rate steady.

    As to why does drift occur? I don't think I *know* the answer to that but I've heard that it has to do with the blade and also, more importantly, how that blade is riding on the tires of the band saw. Also a possible factor is the coplaner-ness of the wheels. Anyway, since I'm also a beginner resawer i've collected a few links dealing with the subject:


    http://www.highlandwoodworking.com/i...OD&ProdID=6076

    http://www.suffolkmachinery.com/default.asp

    http://www.rd.com/americanwoodworker...s/200008/main/

    http://www.highlandwoodworking.com/i...n=Custom&ID=24

    Suffolk is where I got my blades they are very helpful on the phone making sure you get the correct thing, although their blade tensioning method is a bit confusing to me. They also have a very interesting catalog that has more than just product listings but includes good info, you should order a free copy.

    The American Woodworker article linked above is what hooked me on resawing.

    Good luck! If you come across any other cool sites or links send them on over!

    Oh, here is a board I was practicing on:
    http://www.teraflax.com/Fine.cut.bandsaw/

    Kinda cool!

    - BD

    Leave a comment:

Working...