HF DC won't roll without casters catching

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • dlminehart
    Veteran Member
    • Jul 2003
    • 1829
    • San Jose, CA, USA.

    #1

    HF DC won't roll without casters catching

    My new HF DC seems to have caster shanks that are about 1/2" too short. When the casters pivot, they can hang up on the edges of the platform to which they're attached. Did I hook them up wrong? Anyone else have the problem? Any easy way to fix it?
    - David

    “Be yourself; everyone else is already taken.” -- Oscar Wilde
  • bmyers
    Veteran Member
    • Jun 2003
    • 1371
    • Fishkill, NY
    • bt 3100

    #2
    Oh good. I thought it was me.

    Bill
    "Why are there Braille codes on drive-up ATM machines?"

    Comment

    • sscherin
      Senior Member
      • Dec 2003
      • 772
      • Kennewick, WA, USA.

      #3
      It's a common problem.. just make some spacers to go between the casters and the platform
      William's Law--
      There is no mechanical problem so difficult that it
      cannot be solved by brute strength and ignorance.

      Comment

      • Pappy
        The Full Monte
        • Dec 2002
        • 10490
        • San Marcos, TX, USA.
        • BT3000 (x2)

        #4
        I think I have one the 3 made that will roll!
        Don, aka Pappy,

        Wise men talk because they have something to say,
        Fools because they have to say something.
        Plato

        Comment

        • LCHIEN
          Super Moderator
          • Dec 2002
          • 22106
          • Katy, TX, USA.
          • BT3000 vintage 1999

          #5
          yeah that problems been well documented here. You should have searched for "HF DC problems" or something like that before assembling anything HF'ish.

          Some guys complain they have black streaks all over their shop because of this!

          I caught it while assembling and put 3/4" wood spacers under each wheel and used 1/4-20 x 1" bolts and nuts instead of the supplied metric ones.
          Others just took some big pliers or hammer and bent the lip outwards as needed to avoid interference (works, but must look like sh*t, tho).
          Another solution - You can probably break off the locking levers since its nearly impossible to lock it anyway.

          apparently they changed wheel suppliers and/or part numbers from non-locking to locking type somewhere in the manufacturing history and never took care of the resulting problems.

          Probably some guy in the purchasing dept said we can buy these other comapany's casters with locks for $0.50 less per DC and they have the same hole pattern.
          In a proper manufacturing organization there is a "Change Review Board" or similar composed of engineers and managers whose duty it is to review proposed changes in suppliers and materials to see if there is any possible effects - and would assign an engineer to actually do the tests and or computations if there were - he'd then have to reject the new part number, propose an alternate or redesign the assembly to handle the new part.
          Loring in Katy, TX USA
          If your only tool is a hammer, you tend to treat all problems as if they were nails.
          BT3 FAQ - https://www.sawdustzone.org/forum/di...sked-questions

          Comment

          • autiger1
            Senior Member
            • Jan 2003
            • 549
            • Tampa, Florida, USA.

            #6
            I just used some scrap oak and made spacers.

            Tom

            Comment

            • Carlos
              Veteran Member
              • Jan 2004
              • 1893
              • Phoenix, AZ, USA.

              #7
              I got out the Vise Grips and bent the sheet metal just a bit to clear the wheels. 1 minute job.

              Comment

              • dlminehart
                Veteran Member
                • Jul 2003
                • 1829
                • San Jose, CA, USA.

                #8
                Loring, I did a number of searches, but either got nothing useful or too much to wade through. 'Twould be nice if the searches had a word proximity option, rather than just AND and OR.
                - David

                “Be yourself; everyone else is already taken.” -- Oscar Wilde

                Comment

                • LCHIEN
                  Super Moderator
                  • Dec 2002
                  • 22106
                  • Katy, TX, USA.
                  • BT3000 vintage 1999

                  #9
                  quote:Originally posted by dlminehart

                  Loring, I did a number of searches, but either got nothing useful or too much to wade through. 'Twould be nice if the searches had a word proximity option, rather than just AND and OR.
                  got this one searched for "HF DC Wheel problems"
                  http://www.bt3central.com/forum/topi...Wheel,problems
                  got this one searched for "HF DC Assembly problems"
                  http://www.bt3central.com/forum/topi...embly,problems
                  Loring in Katy, TX USA
                  If your only tool is a hammer, you tend to treat all problems as if they were nails.
                  BT3 FAQ - https://www.sawdustzone.org/forum/di...sked-questions

                  Comment

                  Working...