Dual-Width Extension Wing

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #31
    Larry

    I'm going to do this build so if you want to email me a sketch I'll post up a sketch up file for everyone else to be able to use. My half rails are on their way
    パトリック
    daiku woodworking
    ^deshi^
    neoshed

    Comment


    • #32
      Originally posted by siliconbauhaus View Post
      Larry

      I'm going to do this build so if you want to email me a sketch I'll post up a sketch up file for everyone else to be able to use. My half rails are on their way
      Where did you get your rails?
      Thom

      Comment


      • #33
        No plans arrived yet!!

        Larry: Please re-send the plans -- they did not make it the first time.
        Thom

        Comment


        • #34
          I posted on here I was looking for a half set of rails mate.
          パトリック
          daiku woodworking
          ^deshi^
          neoshed

          Comment


          • #35
            If I may also chime in to request the posting of the plans. Most kindly appreciated!

            Comment


            • #36
              BT3xx0 Rails

              Contact Jim Cherry at jcherryai@hotmail.com. I'm getting a set for the BT3100 at 81.00. He's located in Indiana. Also the 3100 and 3000 are different fitment besides the colour.

              Regards,
              George

              Comment


              • #37
                Originally posted by George Cole View Post
                Contact Jim Cherry at jcherryai@hotmail.com. I'm getting a set for the BT3100 at 81.00. He's located in Indiana. Also the 3100 and 3000 are different fitment besides the colour.

                Regards,
                George
                All the important parts of the two different rail extrusions line up though. Check out posts 5 & 6 of this thread: http://www.bt3central.com/showthread.php?t=45948
                Erik

                Comment


                • #38
                  Thom, I had a glitch on my end, so I'll send the plans again. Sorry for the delay; as usual, I've been offline all weekend and only saw your PM a few minutes ago.

                  Patrick, I'll send them to you at the same time.

                  IWannabe, the plans are in PDF format. If you'll send me a PM containing your email address, I'll send them to you as well.
                  Larry

                  Comment


                  • #39
                    I'd appreciate if you'd send me a copy as well.

                    Thanks.
                    Bill

                    Comment


                    • #40
                      Dual-Width Extension Wing

                      Hey Larry, can you send me a copy of the plans. This design is really good, I was looking if I could put leg's on it?

                      Comment


                      • #41
                        Originally posted by emcmsw View Post
                        Hey Larry, can you send me a copy of the plans. This design is really good, I was looking if I could put leg's on it?
                        Plans sent this morning, to the email address you provided in your PM.

                        I presume you mean adding legs under the ends of the rails; or folding/removable legs on the Dual-Width Extension Wing itself. Either is possible but shouldn't be necessary unless you made your DWEW a lot bigger or heavier than mine. As I wrote back in May 2007, my DWEW had at that time been mounted continuously on the saw for a full year, with no additional support under the rails, with no problem. Those BT rail extrusions are pretty stout!
                        Larry

                        Comment


                        • #42
                          Resurrecting an old thread.

                          I had a copy of the plans from LarryG long ago bit have since lost them.

                          Anyone with a copy they could forward my way?

                          Thanks
                          Robert

                          Comment


                          • #43
                            This is a supercool design (sorry I am a newbie catching up). If someone has the plans can they please post them here for everyone's benefit.

                            Thanks

                            NG

                            Comment


                            • #44
                              The author has not been on since 2015.
                              I send him a private mail alerting him to interest in his plans.
                              No idea if he will get it.

                              Larry if you get this far, you can now upload and attach PDFs and other such files to the posts and replies.

                              Loring
                              Loring in Katy, TX USA
                              If your only tool is a hammer, you tend to treat all problems as if they were nails.
                              BT3 FAQ - https://www.sawdustzone.org/forum/di...sked-questions

                              Comment

                              Working...
                              X