tuning a new drill press

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • milanuk
    Established Member
    • Aug 2003
    • 287
    • Wenatchee, WA, USA.

    #1

    tuning a new drill press

    The thread about all the neat things you can do w/ a drill press brought to mind a question when someone mentioned being able to drill perfectly perpendicular holes.

    Question is, how do you (as in you, personally) go about making *sure* that your drill press is perfectly set up for 90°?

    Just go by the angle indicator on the table? Use a square and a long drill bit? One method I saw in a magazine somewhere this summer involved drilling holes in a block of MDF, and then sticking a precision-ground rod in the resulting hole and measuring whether it was then perpendicular w/ the surface. Seemed a little overboard to me at the time, but now that I have a brand-spankin-new DP400, I'm wondering...

    TIA,

    Monte
    All right, breaks over. Back on your heads!
  • LCHIEN
    Super Moderator
    • Dec 2002
    • 22099
    • Katy, TX, USA.
    • BT3000 vintage 1999

    #2
    I square mine against the table.
    I use a stiff, straight metal rod or a good bit (like 1/4 to 1/2") chucked up and made sure to have minimal runout.
    Then check the squareness to the table in both the right left plane and check the front-back plane (not sure what to do about it if its not...!).
    Set the table square to the blade by adjusting the table tilt and then verify it says zero and adjust the indicator (if possible).

    I also try to get the table flat dead level to a bubble level by shimming the whole drill press. This ensures the bit is aboslutely perpendicular to, and the table is parallel to, the plane of the earth's surface.

    By having the bubble level flat dead I can drill square into the end of long pieces of wood and dowel by using the vertical bubbles of a level to check the item usually clamped at the very bottom is perfectly upright.

    I haven't checked these for a long time... but do so every once in a while. I don't expect them to go out and haven't had any fit/drill problems indicating this might have happened.
    Loring in Katy, TX USA
    If your only tool is a hammer, you tend to treat all problems as if they were nails.
    BT3 FAQ - https://www.sawdustzone.org/forum/di...sked-questions

    Comment

    • Stick
      Senior Member
      • Sep 2003
      • 872
      • Grand Rapids, MB, Canada.
      • BT3100

      #3
      quote:Originally posted by milanuk


      Question is, how do you (as in you, personally) go about making *sure* that your drill press is perfectly set up for 90°?

      One method I saw in a magazine somewhere this summer involved drilling holes in a block of MDF, and then sticking a precision-ground rod in the resulting hole and measuring whether it was then perpendicular w/ the surface. Seemed a little overboard to me at the time, but now that I have a brand-spankin-new DP400, I'm wondering...

      TIA,

      Monte
      What Loring said. I use drill rod and machinist's square to check the table, and a machinist's level to check the whole machine's level. I bolt mine down to the floor, so that never moves. The 90° stops are often inaccurate on consumer type drill presses. Don't trust them until you check them.

      Comment

      • Stytooner
        Roll Tide RIP Lee
        • Dec 2002
        • 4301
        • Robertsdale, AL, USA.
        • BT3100

        #4
        If the table on a DP is a little wonky from front to back, you can loosen up the bolt that adjusts the left and right tilt. Slip aa shim or an old feeler guage in at the top of the crack or bottom as needed and tighten back up.
        Lee

        Comment

        • leehljp
          The Full Monte
          • Dec 2002
          • 8804
          • Tunica, MS
          • BT3000/3100

          #5
          Simplicity:
          Mark "Woodmangler" had the most simple setup that I have ever seen. He chucked a 12 to 15 inch piece of coat hanger wire. It came out of the chuck, was bent to a semi- right angle by hand for about 4 or 5 inches and then bent down to the table. It does not have to be pretty. Rotate the spindle by hand and see where it touches and where it does not touch and adjust from there. When it barely touches all the way around, the table is square with the chuck, period! [8D]
          Hank Lee

          Experience is what you get when you don't get what you wanted!

          Comment

          • jstevens
            Established Member
            • Dec 2003
            • 125
            • Ardmore, PA, USA.

            #6
            quote:Originally posted by LCHIEN

            check the front-back plane (not sure what to do about it if its not...!).
            That's exactly the problem my drill press has. For anyone planning on making a table to fit over the original one, it's pretty easy to compensate for the tilt when designing and making the table. Plenty of ways to skin that cat--shims, adjusting screws, gradually trim shavings off the base with a plane until level, etc.

            Otherwise, I'm not sure what you would do. My Ridgid DP has no provision for adjustment in that direction. Perhaps more expensive DPs do?

            Regards,

            John

            Comment

            • vinht
              Established Member
              • Jan 2004
              • 391
              • North Andover, MA, USA.

              #7
              quote:Originally posted by jstevens

              quote:Originally posted by LCHIEN

              check the front-back plane (not sure what to do about it if its not...!).
              That's exactly the problem my drill press has. For anyone planning on making a table to fit over the original one, it's pretty easy to compensate for the tilt when designing and making the table. Plenty of ways to skin that cat--shims, adjusting screws, gradually trim shavings off the base with a plane until level, etc.

              Otherwise, I'm not sure what you would do. My Ridgid DP has no provision for adjustment in that direction. Perhaps more expensive DPs do?

              Regards,

              John
              I'm new to drill presses since I just got mine yesterday. The first thing I did was search online for tuning instructions. Unfortunately, all I found were books on the subject.

              Regarding the table being level, as long as the bit is perpendicular to the table does it matter if it's level in relation to the floor or in my case the bench top? Kind of like the torsion box theory?

              Vinh
              A Woodworker\'s Journey
              http://vinht.home.comcast.net

              Comment

              • LCHIEN
                Super Moderator
                • Dec 2002
                • 22099
                • Katy, TX, USA.
                • BT3000 vintage 1999

                #8
                quote:Originally posted by vinht

                quote:Originally posted by jstevens

                quote:Originally posted by LCHIEN

                check the front-back plane (not sure what to do about it if its not...!).
                That's exactly the problem my drill press has. For anyone planning on making a table to fit over the original one, it's pretty easy to compensate for the tilt when designing and making the table. Plenty of ways to skin that cat--shims, adjusting screws, gradually trim shavings off the base with a plane until level, etc.

                Otherwise, I'm not sure what you would do. My Ridgid DP has no provision for adjustment in that direction. Perhaps more expensive DPs do?

                Regards,

                John
                I'm new to drill presses since I just got mine yesterday. The first thing I did was search online for tuning instructions. Unfortunately, all I found were books on the subject.

                Regarding the table being level, as long as the bit is perpendicular to the table does it matter if it's level in relation to the floor or in my case the bench top? Kind of like the torsion box theory?

                Vinh
                If the table is not perpendicular to the bit front to back, then the DP is defective IMHO.

                As for the table being level, I explained that.
                Its not neceeesary to drilling but when setting up tall pieces to be drilled, you can make the piece vertical with a bubble level and be assured you are going straight in the end. Otherwise, its difficult.
                Loring in Katy, TX USA
                If your only tool is a hammer, you tend to treat all problems as if they were nails.
                BT3 FAQ - https://www.sawdustzone.org/forum/di...sked-questions

                Comment

                • vinht
                  Established Member
                  • Jan 2004
                  • 391
                  • North Andover, MA, USA.

                  #9
                  Thanks for the clarification Loring, I think I understand.

                  By the way, Monte, I found this online. Not sure how well it would work though....

                  http://www.woodworkingtips.com/woodtips/wbtip05.html

                  I'm thinking of getting this book. Anyone have this?

                  http://www.amazon.com/exec/obidos/AS...696142-7318338

                  Vinh
                  A Woodworker\'s Journey
                  http://vinht.home.comcast.net

                  Comment

                  • LarryG
                    The Full Monte
                    • May 2004
                    • 6693
                    • Off The Back
                    • Powermatic PM2000, BT3100-1

                    #10
                    quote:Originally posted by vinht

                    Regarding the table being level, as long as the bit is perpendicular to the table does it matter if it's level in relation to the floor or in my case the bench top?
                    Although not strictly necessary for a drill press (except for situations such as Loring described), I'm a big believer in having everything in the shop as close to perfectly level and plumb as possible. If things are sitting cattywampus, your eye will be fooled and you'll have a harder time judging when your projects are assembled nice and square, like they're supposed to be, and when they're out of whack. A critical eye is one of your most important tools; you don't want to give it any unnecessary obstacles to overcome.
                    Larry

                    Comment

                    • Tom Miller
                      Veteran Member
                      • Mar 2003
                      • 2507
                      • Twin Cities, MN
                      • BT3000 - Cuttin' it old school

                      #11
                      For those of you with a dial indicator:



                      I suggest rotating the chuck by hand. [B)]

                      Regards,
                      Tom

                      Comment

                      • milanuk
                        Established Member
                        • Aug 2003
                        • 287
                        • Wenatchee, WA, USA.

                        #12
                        quote:Originally posted by vinht


                        I'm thinking of getting this book. Anyone have this?

                        http://www.amazon.com/exec/obidos/AS...696142-7318338

                        Vinh
                        Ya know, I do. And I completely friggin' forgot about there being drill press stuff in it

                        I'll take a look at it in the morning when I get off work and see what it has to say and let you know. I remember looking a lot at the stuff on the jointer and for a 'regular' i.e. non BT3K table saw and it was pretty detailed and informative for people like me who have no one else more experienced at hand for a mentor.

                        Monte
                        All right, breaks over. Back on your heads!

                        Comment

                        • gjsgjsgjs
                          Forum Newbie
                          • Feb 2004
                          • 26
                          • Minneapolis, MN, USA.

                          #13
                          even cheaper at overstock.com

                          http://www.overstock.com/cgi-bin/d2....PROD_ID=158396

                          Comment

                          Working...