Threaded Inserts ????
Collapse
This topic is closed.
X
X
-
More importantly, there are separate (different) parts for hardwoods and softwoods, and they don't say which ones are best for Plywood!
http://www.ezlok.com/InsertsWood/softWood.html
http://www.ezlok.com/InsertsWood/hardWood.html
I think there are some differences in application between the threaded inserts with threaded bodies and the ones we also sometimes call T-nuts withthe little barbs and the flange.
The t-nut/barbed/flange ones have no pullout strength at all from the insertion side, they must be pulled into the wood meaning pul from the other side.
The external thread screw-in threaded inserts like Mike McCoy references and the OP is trying to use, have theoretical very high pull out strength from side opposite the insertion side, but should also be pretty good from the insertion side meaning they can be used blind (whereas the T-nuts cannot).
Now some of those flanged T-nuts can be had with mounting holes in the flange instead of barbs... that would help hold it in but the screws are generally pretty small.
Note also in the E-Z lok instructions it advises for the Hardwod ones that you should sink it 1/16th below the surface for max strength. One of the posters advised using a washer to set it flush - that would not be a good idea to set it flush, then.
I think the OP should call or e-mail EZ-lok asking for their recommendation for Plywood...
I think all the people who epoxy these things in are doing something the manufacturer did not intend for you to do... they were intended to be used dry or maybe with some thread lube (they recommended varnish) and the threads providing the holding power.Last edited by LCHIEN; 09-17-2007, 09:47 AM. -
Here you go - there are separate charts for softwood and hardwood.
http://www.ezlok.com/InsertsWood/hardWood.htmlLeave a comment:
-
Does anybody know if there is an article or chart showing what size hole to drill for thread insert? Also does anyone know what shopnotes or wood magazine the article was in?
Thanks.Leave a comment:
-
I like McMaster Carr but I got a new catalog from McFeely's today and have to comment they have a lot of variety. They have small sizes and also have Brass, Steel, and Stainless steel. Plus they have a couple of varieties that you drive in with a hex wrench.
JimLeave a comment:
-
I orderd mine from McMaster Carr.com . They worked great in My router table top for leveling the router plate w/plastic thumb screws.
Also the ones I ordered take a allen wrench to install!
Last edited by BT3 WOODOG; 07-10-2007, 04:06 PM.Leave a comment:
-
I ordered the shorter barbed versions this am (1/2 inch) and I'll try the clamped technique w/ expoxy for the back of the fences as I want to have a clean face design. For the areas that I can't clamp I'll try the ideas above so thanks everyone, pictures should be posted for both the drill press and router table as soon as I can install the parts !!!Leave a comment:
-
-OR-I have discovered that the ones with barbs, straight from our small town hardware store, work beautifully if, instead of using a hammer, you position it over the hole and use a C-clamp head or vise to press it in, slowly tightening the pressure until it goes in all the way.
If you can get at the "rear" - using a fender washer and a 1/4" studded knob (or a bolt), just tighten it in
Leave a comment:
-
I have discovered that the ones with barbs, straight from our small town hardware store, work beautifully if, instead of using a hammer, you position it over the hole and use a C-clamp head or vise to press it in, slowly tightening the pressure until it goes in all the way.Leave a comment:
-
I also like Lee Valley for hardware and also Hartville tool. I think it is Hartville that has little 8x32 inserts if you ever need those. Lee Valley's smallest is 1/4 inch, if I remember right. Hartville's are brass plated steel and I think Lee Valley's are brass.
JimLeave a comment:
-
I use the threaded inserts, not the barbed ones. The trick to these little buggers is to drill the correct size hole the correct depth, clean it from debris, and make sure it is straight (90 deg to the panel). Then turn in the insert. They work best being inserted once and are much better than the barbed ones.
.Leave a comment:
-
Without looking I don't know whether either will have exactly what you need, but I buy most jig and fixture hardware from either Lee Valley or Woodpeckers -- the latter when possible, as they tend to have more reasonable prices on this sort of stuff than most vendors.Leave a comment:
-
In response, the applications are bolting my drill press table top to the drill press original metal table (four 5/16 x 1 bolts coming up from underneath), the back side of left / right sliding router fences, and custom vertical material hold down clamps for the table. I went to Rockler and the guy there wasn't much help and he said "I never have a problem I don't know why you do .... buy my $11 insert bit " !!! I bought the barbed inserts and they had some cheapie epoxy but the barbed inserts are 3/4 inch and the stock I'm using is also 3/4. I'll cut them down and see how it goes ...
Now that I'm frustrated at Rockler talent / parts what other sources besides Lowes that Pappy mentioned do you get the brass / steel inserts that worked well and right the first time for you all ?????Last edited by movnup; 07-06-2007, 11:34 AM.Leave a comment:
-
I recently did a project that needed to be easily assembled/disassembled, so it used a LOT of 3/8" threaded inserts. I took a bolt, cut off its head, and threaded two nuts with a lock washer between them. About 1/2" of bolt protruding below the nuts. Then, I chucked this contraption into a regular hand drill and put a bit of oil on the bolt and lower nut.
The insert is threaded onto the bolt till it is against the lower nut, then you hold the drill as close to a right angle as you can get, and put the insert in. Use low speed - about 1-2 rotations per second. On my Dewalt, I was just barely pressing the switch.
Once the insert is all the way in, switch into reverse, and give the trigger a good squeeze. The fast speed and oil should disengage the bolt from the insert, leaving it in place. It took me less than a minute per insert this way. There were a couple of stubborn ones that caught and would try to come out along with bolt - for those, I'd unchuck the bolt, and use one wrench to hold lower nut while I loosened the upper one, and then holding the bold with vise-grip while I losoened the lower nut from the insert.
Aside from those few, I got 50+ inserts perfectly seated with no fuss in less than an hour.Leave a comment:
-
I have had good success with harbour freight 5 minute epoxy. I was pleasantly surprised.
I have also used a lot of screw in inserts like these. I cannot quite picture your application but when the hole depth permits, I find it handy to have an inch or more of bolt going through the insert. That gets me well aligned before screwing the insert into the hole. When I want to be extra sure it does not split the wood or bulge it out, I drill an oversized hole and use the epoxy to hold the insert. I have used #8 threaded inserts up to 3/8 inch and they all work. I've put them in particle board, MDF, oak, and pine. Maybe some others I am forgetting. Larger holes for hardwood but otherwise they seem to work well.
I do not like the hammer in variety. The ones I used are made of zinc which is soft and less durable than brass or steel which is what is generally used in the screw in variety. I've had the inserts pull out and also had the machine threads pull out of the inserts. I haven't had either problem with the screw in type.
JimLeave a comment:
-

LCHIEN
Leave a comment: