The Wood Magazine jig I built mimics Shop Notes drill press idea with the double nut and the bolt w/ washer threading it in. I called Rockler and he thought the barbed version banging it in and with the popular wood fences the ones i had were supposed to work !!! I'm going over to Rockler after work and try the barbed version with epoxy as that sounds like the ticket for ply.
I'm also going to try chamfering the edges first as mentioned above and that I saw in a Woodcraft article. Great feedback everyone !!!
Can anyone recomend a brand / type of epoxy they like as the HD version I used didn't hold ???
Threaded Inserts ????
Collapse
This topic is closed.
X
X
-
Can you switch to the style Joe was referring to (with barbs)?
Seen here:
http://www.rockler.com/product.cfm?p...eaded%20insert
I've used 'em in plywood and they hold great. You can apply epoxy to the hole before you knock 'em in, if you feel that is necessary. I never found it to be.
If I was really concerned about strength, I'd use a barbed insert, and counter-sink the hole for the flange. Then I'd epoxy it and bang it in.Leave a comment:
-
I've used the brass inserts that Lowe's sells on several projects. Always into solid stock, not plywood. I play with some scrap with different size holes until I find one that threads in good. I also slightly chamfer the edge of the hole so the initial bite is in the wood a little.
With the courseness and depth of the threads, I would think they would pull hard enough on the plywood to tear through the laminations before they could get a good bite.Leave a comment:
-
There was a wood-mag somewhere (shopnotes?) that suggested putting a bolt in your drill press and double nutting the insert onto that bolt. Then twist the insert into the wood by turn the drill manually and press slightly with downward motion of the press.
That way it goes in straight and you have some grip behind it.
HTH,
BillLeave a comment:
-
I installed those into my workbench (MDF) using the method described in Workbench magazine. They drilled a slightly oversize hole, the threads of the insert should barely dig in (my inserts just set in without any screwing). Put masking tape on the bottom of the insert and put epoxy in the hole. Screw a small bolt and fender washer into the threaded insert and drive it in with the bolt. The washer keeps it flush with the table surface and the epoxy does the real holding. It works like a charm for my miter saw fence.
I'll see if I have that article lying around and can scan it for you.
If the hole is tite and you screw those inserts in you sometimes get buckling in the wood around it which isn't nice, you also run into the problem of there not being enough surface area for the epoxy to hold onto.Leave a comment:
-
Screw thread ... if you hammered them in why would you have a screw thread / screw w/ barbs on the thread / screwdriver slot on both versions on the top of them ????
I sure would love to take a hammer to them that's for sure
From Rockler's website:
Made from steel. Size listed is the size of the internal machine threads.
Sold in pack of 8.
Can be installed with screwdriver, threaded insert wrench or threaded insert power drive tool.Last edited by movnup; 07-05-2007, 12:41 PM.Leave a comment:
-
If they're the inserts that I think they are, they're meant to be hammered or pressed in. If you're spinning them, then the barbs that are supposed to hold them in place are going to chew up the wood like a rasp, and they won't work.
Does the outside of the insert have a bunch of barbs running along the axis, or does it have a screw thread?Leave a comment:
-
Threaded Inserts ????
I'm finishing up my drill press and router table and am having problems getting the threaded inserts to start / stay in. I'm using Rocklers insert for a 5/16 t-bolt but in using a 3/8 (recomended), 7/16, and also 1/2 guide hole I can't get them to thread in. I also built the jig they had in wood magazine that centers a vertical bolt w/ washer and double nut over the insert then using a ratchet and still no luck. I've also tried different woods - birch ply (the tops), poplar (fences), and oak (hardwood test).
Going down the list I've tried wood titebond, construction adhesive, epoxy, and gorilla glue in the process but none of them stop them from spinning. Such a simple concept but do they even work in birch plywood / do I need a different brand / what am I doing wrong ?????Tags: None

Leave a comment: