Chess Table

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • reddog552
    Established Member
    • Dec 2006
    • 245
    • Belleville Il.
    • Bt3000

    #1

    Chess Table

    Just finnished. This was made from old beat up craftsman blanket chest (Fine Pine)Mom made the ceramic chess pcs.. I have app. 100 squares left over, U woulnt believe how hard it was to cut 64 pcs.the same exact size. Played with different setups for hours to get them right. Finally made a sliding table with stops.
    Last edited by reddog552; 07-30-2009, 11:34 AM.
    The bitterness of poor quality lingers long after the sweetness of low cost is forgotten!
  • klefkow
    Forum Newbie
    • Apr 2006
    • 17

    #2
    Chess board

    A little late for you but this will help anyone else making a chess board.

    http://www.metacafe.com/watch/463464...uick_easy_way/

    Comment

    • reddog552
      Established Member
      • Dec 2006
      • 245
      • Belleville Il.
      • Bt3000

      #3
      Duh

      That was easy
      The bitterness of poor quality lingers long after the sweetness of low cost is forgotten!

      Comment

      • LCHIEN
        Super Moderator
        • Dec 2002
        • 22047
        • Katy, TX, USA.
        • BT3000 vintage 1999

        #4
        the classic way of making a chssboard is to rip 8 lengths of alternating light and dark; the same consistent width should be achievable with a good table saw and featherboards.
        Then join (edge glue) them in into a board with alternating light and dark strips 8 wide.
        Then rip the cross direction to get strips of light/dark squares the same rip setting used before.
        Then flip every other strip end for end arriving at a checkerboard pattern. Join them edge to edge (glue-up again) and you get a perfect chessboard matching squares fits perfectly.
        If you want small contrast strips between the squares then you can picture ripping them and laminating them between the L&D strips.

        P.S. Oh, shudda looked at the video Klefow posted first... that's the exact same method i described.
        Last edited by LCHIEN; 07-04-2009, 11:19 AM.
        Loring in Katy, TX USA
        If your only tool is a hammer, you tend to treat all problems as if they were nails.
        BT3 FAQ - https://www.sawdustzone.org/forum/di...sked-questions

        Comment

        • radhak
          Veteran Member
          • Apr 2006
          • 3061
          • Miramar, FL
          • Right Tilt 3HP Unisaw

          #5
          That's a lovely board, reddog! how did you get the dark colors?

          And did you say your mom made the pieces? How does she do that ??!!
          It is the mark of an educated mind to be able to entertain a thought without accepting it.
          - Aristotle

          Comment

          • reddog552
            Established Member
            • Dec 2006
            • 245
            • Belleville Il.
            • Bt3000

            #6
            table

            The stains were Golden oak & Black walnut. Mom made the pieces In ceramics then fired them red & black
            The bitterness of poor quality lingers long after the sweetness of low cost is forgotten!

            Comment

            • lrogers
              Veteran Member
              • Dec 2002
              • 3853
              • Mobile, AL. USA.
              • BT3000

              #7
              Very, very nice. A chess board is still one of "someday projects" for me.
              Larry R. Rogers
              The Samurai Wood Butcher
              http://splash54.multiply.com
              http://community.webshots.com/user/splash54

              Comment

              • phrog
                Veteran Member
                • Jul 2005
                • 1796
                • Chattanooga, TN, USA.

                #8
                Great work reddog. Really nice board. Your Mom did a great job also.
                Richard
                Richard

                Comment

                • SARGE..g-47

                  #9
                  Very nice Reddog... wouldn't be interested in coming over and installing a parquet floor in my entrance-way would you....? Your mom did good on the ceramic chess set also. Although I don't find time to play anymore.. an old girl-friend from down in Austrailia made me a cerarmic set back in the early 70's which is quite nice. The bad news is none of my downfall lumber would fit in her kiln.

                  Comment

                  • GPA61
                    Senior Member
                    • Sep 2004
                    • 712
                    • Rancho Cucamonga, CA
                    • BT 3100 & JET JWTS

                    #10
                    Great work.
                    Claudio

                    Comment

                    • John Hunter
                      Veteran Member
                      • Dec 2004
                      • 2034
                      • Lake Station, IN, USA.
                      • BT3000 & BT3100

                      #11
                      Very nice.
                      John Hunter

                      Comment

                      • jhart
                        Veteran Member
                        • Feb 2004
                        • 1715
                        • Minneapolis, MN, USA.
                        • BT3100

                        #12
                        Great looking board and chess set. Chessboard has been on my to do list for years. Still haven't gotten around to doing it!!
                        Joe
                        "All things are difficult before they are easy"

                        Comment

                        • Uncle Cracker
                          The Full Monte
                          • May 2007
                          • 7091
                          • Sunshine State
                          • BT3000

                          #13
                          Originally posted by klefkow
                          A little late for you but this will help anyone else making a chess board.

                          http://www.metacafe.com/watch/463464...uick_easy_way/
                          That hearkens me back to my high school shop days. My son still has the chessboard I made using this method...

                          Comment

                          • Alex Franke
                            Veteran Member
                            • Feb 2007
                            • 2641
                            • Chapel Hill, NC
                            • Ryobi BT3100

                            #14
                            Originally posted by LCHIEN
                            the classic way of making a chssboard is to rip 8 lengths of alternating light and dark; the same consistent width should be achievable with a good table saw and featherboards.
                            If you have a band saw and you're short on wood, you can use my shortcut: Rip 2 lengths, edge glue them, resaw into 4, edge-glue again, then cross-cut. It comes out beautifully every time! (Lots of details and photos here: http://plans.thefrankes.com/Tutorial...d/Default.aspx)
                            online at http://www.theFrankes.com
                            while ( !( succeed = try() ) ) ;
                            "Life is short, Art long, Occasion sudden and dangerous, Experience deceitful, and Judgment difficult." -Hippocrates

                            Comment

                            • footprintsinconc
                              Veteran Member
                              • Nov 2006
                              • 1759
                              • Roseville (Sacramento), CA
                              • BT3100

                              #15
                              looks real nice. the ceramic pieces are very beautiful as well.
                              _________________________
                              omar

                              Comment

                              Working...