(edited on 4/27/2008 to re-insert pictures)
I got tired of tripping over, moving around, and rummaging through my unorganized pile of stock. I also needed some place to put my "cull" pieces and good cutoffs. First, the lumber rack (2/3rds complete):

I borrowed heavily from dlminehart's rack that he posted. This rack is in my basement shop, along the "old" foundation wall that's now the interior of the new half of the basement. The "curb" of the drop from the old floor level to the new floor level gave a nice platform for sheet good storage. Plus, it doesn't impede on floor space, because the lumber rack is flush with the curb. The 2x4 studs are anchor-sleeved to the wall, four per stud. That's probably overkill. . . but I didn't want to risk collapse. The spacing between studs (23" OC) is a little wider than I'd like, because a 6' board rests just on-center of the outer two horizontal supports in a four-support stretch. I thought I planned for a 21" OC spacing, but I must have made a change somewhere along the way that I can't remember. Oh well.
I did make a few changes to Dave's excellent system. I used 3/4" EMT conduit. That required use of a 15/16" spade bit at 5-degrees for the horizontal supports. I had to use a spade bit because that's all I could find in that size. A 29/32" bit would have been perfect, because there is a gap in a 15/16" hole. I used two wraps of aluminum tape to get a snug fit; I couldn't find any of the curtain rod stuff that Dave used.
Here is the complete version.

I can fit 8 full sheets of 3/4" plywood in the sheet good section, plus a various amounts of other remnant thicknesses in the left-most lower section. Those vertical padded conduit supports are loose-fit so that I can pull them out easily. I'm pleased with the result, and I'd be happy to provide more details if anybody wants them.
Finally, I needed a place to put my "cull" pieces that are too good to throw away, or too useful to burn. So, I made the following entirely out of HD cull rack material. It's a mix of 1/2", 3/4", and 1/4" MDF, with a 1/4" BC plywood back. I didn't follow a plan. . I just made it up as I went along. It's difficult to tell in the photo, but there are 6 "bays" in my cull-bin cull bin.
I got tired of tripping over, moving around, and rummaging through my unorganized pile of stock. I also needed some place to put my "cull" pieces and good cutoffs. First, the lumber rack (2/3rds complete):
I borrowed heavily from dlminehart's rack that he posted. This rack is in my basement shop, along the "old" foundation wall that's now the interior of the new half of the basement. The "curb" of the drop from the old floor level to the new floor level gave a nice platform for sheet good storage. Plus, it doesn't impede on floor space, because the lumber rack is flush with the curb. The 2x4 studs are anchor-sleeved to the wall, four per stud. That's probably overkill. . . but I didn't want to risk collapse. The spacing between studs (23" OC) is a little wider than I'd like, because a 6' board rests just on-center of the outer two horizontal supports in a four-support stretch. I thought I planned for a 21" OC spacing, but I must have made a change somewhere along the way that I can't remember. Oh well.
I did make a few changes to Dave's excellent system. I used 3/4" EMT conduit. That required use of a 15/16" spade bit at 5-degrees for the horizontal supports. I had to use a spade bit because that's all I could find in that size. A 29/32" bit would have been perfect, because there is a gap in a 15/16" hole. I used two wraps of aluminum tape to get a snug fit; I couldn't find any of the curtain rod stuff that Dave used.
Here is the complete version.
I can fit 8 full sheets of 3/4" plywood in the sheet good section, plus a various amounts of other remnant thicknesses in the left-most lower section. Those vertical padded conduit supports are loose-fit so that I can pull them out easily. I'm pleased with the result, and I'd be happy to provide more details if anybody wants them.
Finally, I needed a place to put my "cull" pieces that are too good to throw away, or too useful to burn. So, I made the following entirely out of HD cull rack material. It's a mix of 1/2", 3/4", and 1/4" MDF, with a 1/4" BC plywood back. I didn't follow a plan. . I just made it up as I went along. It's difficult to tell in the photo, but there are 6 "bays" in my cull-bin cull bin.




Comment