Skil 30 pc 1/4" shank router bit set. (Proceeds to BT3Central).

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • pelligrini
    Veteran Member
    • Apr 2007
    • 4217
    • Fort Worth, TX
    • Craftsman 21829

    #16
    How about $50.

    In spite of David's opinion on Skill bits http://www.bt3central.com/showthread.php?t=49151 I'd rather get the skill set for very occasional use with my Colt than spend a $100+ shipping on new MLCS set. The proceeds go to a good cause too.
    Erik

    Comment

    • pelligrini
      Veteran Member
      • Apr 2007
      • 4217
      • Fort Worth, TX
      • Craftsman 21829

      #17
      Originally posted by greenacres2
      The good news is that after she took the failed hard drive to Staples with no success, one of the women at church was able to coax it enough to get 3,300 pictures, over 1,000 songs and her Outlook data out of it. Time to look at the online back-up services.

      Somebody please outbid me. Thank you!!

      earl
      Done, and It's never too late to consider back-up services, but there might be some spilt 0s and 1s that you'll never see again. Back up early and often!
      Erik

      Comment

      • greenacres2
        Senior Member
        • Dec 2011
        • 633
        • La Porte, IN
        • Ryobi BT3000

        #18
        You're my hero today Erik!!

        Once i get out from under the mountain of work at work, finish up the re-skinning of the shed (got to build the doors and finish trim), get started on the picture frames for Mother's Day/LOML's birthday, put the trim on the bookcase, figure out what to do for the shelving on the upstairs landing, start work on the router table, and a few other things--i'll find a spare tool to auction off myself!!

        earl

        Comment

        • dbhost
          Slow and steady
          • Apr 2008
          • 9523
          • League City, Texas
          • Ryobi BT3100

          #19
          Sorry about my slow response... Been out of state in Oklahoma for a family wedding... Are there any other bids?
          Please like and subscribe to my YouTube channel. Please check out and subscribe to my Workshop Blog.

          Comment

          • dbhost
            Slow and steady
            • Apr 2008
            • 9523
            • League City, Texas
            • Ryobi BT3100

            #20
            We've got $50 going once...
            Please like and subscribe to my YouTube channel. Please check out and subscribe to my Workshop Blog.

            Comment

            • dbhost
              Slow and steady
              • Apr 2008
              • 9523
              • League City, Texas
              • Ryobi BT3100

              #21
              $50.00 going twice...
              Please like and subscribe to my YouTube channel. Please check out and subscribe to my Workshop Blog.

              Comment

              • dbhost
                Slow and steady
                • Apr 2008
                • 9523
                • League City, Texas
                • Ryobi BT3100

                #22
                If no other bids come up, I am going to call this auction closed, and the item sold at 10:00 P.M. (Central time zone) tonight. Due to schedules, I may not be able to get to it to post up about it is all... So any last minute stragglers, now's your chance!
                Please like and subscribe to my YouTube channel. Please check out and subscribe to my Workshop Blog.

                Comment

                • dbhost
                  Slow and steady
                  • Apr 2008
                  • 9523
                  • League City, Texas
                  • Ryobi BT3100

                  #23
                  Sold to Pelligrini. PM me your mailing address. Once donation is verified it goes in the mail...
                  Please like and subscribe to my YouTube channel. Please check out and subscribe to my Workshop Blog.

                  Comment

                  • pelligrini
                    Veteran Member
                    • Apr 2007
                    • 4217
                    • Fort Worth, TX
                    • Craftsman 21829

                    #24
                    Done and done, just purchased another Gold Patron for $50.
                    and noticed the status bar go from $2780 to $2830
                    Erik

                    Comment

                    • greenacres2
                      Senior Member
                      • Dec 2011
                      • 633
                      • La Porte, IN
                      • Ryobi BT3000

                      #25
                      Thank you Erik!! And dbhost for the contribution!!

                      earl

                      Comment

                      • Black wallnut
                        cycling to health
                        • Jan 2003
                        • 4715
                        • Ellensburg, Wa, USA.
                        • BT3k 1999

                        #26
                        Originally posted by pelligrini
                        Done and done, just purchased another Gold Patron for $50.
                        and noticed the status bar go from $2780 to $2830
                        Confirmed Dave in case you needed me to look.

                        Thanks to both of you!
                        Donate to my Tour de Cure


                        marK in WA and Ryobi Fanatic Association State President ©

                        Head servant of the forum

                        ©

                        Comment

                        • dbhost
                          Slow and steady
                          • Apr 2008
                          • 9523
                          • League City, Texas
                          • Ryobi BT3100

                          #27
                          No need, but thanks...

                          I need to get this thing shoved in a box and sent off... Chances are shipping will happen on Saturday... I haven't gotten anywhere near a post office before 8:00 P.M. all week...
                          Please like and subscribe to my YouTube channel. Please check out and subscribe to my Workshop Blog.

                          Comment

                          • dbhost
                            Slow and steady
                            • Apr 2008
                            • 9523
                            • League City, Texas
                            • Ryobi BT3100

                            #28
                            Just got confirmation from Erik that he has the set in good condition in his hands. Enjoy it, and thank you again for supporting BT3Central!
                            Please like and subscribe to my YouTube channel. Please check out and subscribe to my Workshop Blog.

                            Comment

                            • pelligrini
                              Veteran Member
                              • Apr 2007
                              • 4217
                              • Fort Worth, TX
                              • Craftsman 21829

                              #29
                              Yep, it was waiting on me when I got home yesterday. It looks like it will be a very useful set. Thanks!

                              I noticed that someone doesn't always clean their bits before they put them away though.
                              Erik

                              Comment

                              • dbhost
                                Slow and steady
                                • Apr 2008
                                • 9523
                                • League City, Texas
                                • Ryobi BT3100

                                #30
                                Try never... I know I should... But I don't.

                                I just clean them on an as needed basis... I probably ought to change that soon.
                                Please like and subscribe to my YouTube channel. Please check out and subscribe to my Workshop Blog.

                                Comment

                                Working...