DC arm for drill press ala Kirby

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • mhoy
    Forum Newbie
    • Dec 2002
    • 36
    • Sunnyvale, CA, USA.

    #1

    DC arm for drill press ala Kirby

    Nifty s/w for a forum. Seems to be used by a number of places.
    Anyway guess things work.

    Mark
  • LCHIEN
    Super Moderator
    • Dec 2002
    • 22104
    • Katy, TX, USA.
    • BT3000 vintage 1999

    #2
    DC arm for drill press ala Kirby

    Inspired by Rod Kirby's dust collector for his drill press I made one too. Being a copycat I wouldn't make a big deal of it except i made some improvements that simplify it a lot.
    The original Kirby arm:

    I simplified mine by getting rid of the big boxes on the ends - makes it smaller, lighter and easier to get in. I made the arms 7" x 1.5", I think Rod's were 2" wide.

    I made the base a simple Ell that you clamp to the DP table with a clamp.

    Instead of T-nuts installed in the arms, I simply drilled a 1/4" hole and countersunk with a 7/16" brad-point and forced the head of a 1/4-20 bolt into it (takes a 7/16" wrench so the points of the hex just dig in). For tightening I used some three-wing knobs which look nice.

    For the nozzle I simply took the one that came with my shop vac, a crevice tool you can buy at Lowes for $5 or so. It has a tapered body so its easy to jam into a 1.375" Forstner-drilled hole. I had to make a right angle thing with enlarged hole area, but you could make a 2" wide rectangular piece with less work. The square area on the end was to be for a split clamp but the wedge fit of the wand made it un-necessary. I should have made just a nice ring on the end.


    Anyway the finished product works well and sucks up the drill chaff.

    Couple of notes:
    I left clearance at the head so I could attach a 1-1/4 X 2-1/2" hose adapter should I need to use a bigger hose.
    In retrospect Probably a 1" wide arm will be more than sturdy enough; I used 1.5" and Rod used 2". Using 1/4 x 20 wing nuts can make it even cheaper to make, they're only a few cents each and easily available instead of a dollar per knob, if on a budget.
    Used Poplar instead of Marine plywood.

    Credit for the original design and thanks for the inspiration to Rod.
    Attached Files
    Last edited by LCHIEN; 08-01-2008, 11:30 PM.
    Loring in Katy, TX USA
    If your only tool is a hammer, you tend to treat all problems as if they were nails.
    BT3 FAQ - https://www.sawdustzone.org/forum/di...sked-questions

    Comment

    • Scottydont
      Veteran Member
      • Aug 2003
      • 2359
      • Edmonds, WA, USA.
      • Delta Industrial Hybrid

      #3
      Very nice Loring. I am going to have to copy that for drilling pen blanks.
      Scott
      "The Laminate Flooring Benchtop Guy"

      Edmonds WA

      No coffee, no worky!

      Comment

      • GeekMom
        Senior Member
        • Dec 2004
        • 752
        • Bonney Lake, WA.
        • Shopsmith Mark V

        #4
        Nice job, Loring.
        Karen
        <><

        Comment

        • RodKirby
          Veteran Member
          • Dec 2002
          • 3136
          • Melbourne, Victoria, Australia.
          • Mao Shan TSC-10RAS

          #5
          Guess I'll have to junk mine and start again

          Just kidding - Great job - there's always a better way.
          Downunder ... 1" = 25.4mm

          Comment

          • boblon
            Senior Member
            • Aug 2003
            • 727
            • Florida, USA.

            #6
            I haven't made me one - yet - but was thinking this may provide a use for the router dust collector tube that comes with the accessory kit. I don't have a use for that piece, but just couldn't throw it away.

            BobL.
            "Good judgement comes from experience. Experience comes from poor judgement."

            Comment

            • Habe
              Established Member
              • Dec 2002
              • 164
              • Indianapolis, IN, USA.
              • 22114

              #7
              Great mods to the original idea. Now I will have to go and build one. I like the idea of the shop vac hose.
              Habe

              Comment

              • final_t
                Veteran Member
                • Nov 2003
                • 1626
                • .

                #8
                BobL: I like that idea, have the same problem with throwing that away also.

                Comment

                • ChrisD
                  Senior Member
                  • Dec 2004
                  • 881
                  • CHICAGO, IL, USA.

                  #9
                  Looks great, Loring! I'm curious: is it effective for spindle-sanding, too? I do not have an OSS and use my DP for this task. I was thinking of constructing a down-draft to add on to my DP table, but if your and Rod's method works well, I'll just copy it.
                  The war against inferior and overpriced furniture continues!

                  Chris

                  Comment

                  • Luckbox
                    Established Member
                    • Nov 2003
                    • 371
                    • Holly Springs, NC

                    #10
                    That is one of the coolest things I have seen
                    I love lamp.

                    Comment

                    • RodKirby
                      Veteran Member
                      • Dec 2002
                      • 3136
                      • Melbourne, Victoria, Australia.
                      • Mao Shan TSC-10RAS

                      #11
                      Loring - Do you have a "wider" nozzle?

                      For example: If you're using (say) a 2" forstner bit in MDF, the crevice tool wont pick up the "curls".

                      This was the reason I went with the large pick-up.
                      Downunder ... 1" = 25.4mm

                      Comment

                      • monte
                        ***** Windbag
                        • Dec 2002
                        • 5242
                        • Paw Paw, MI, USA.
                        • GI 50-185M

                        #12
                        Very nice Loring!
                        Monte (another darksider)
                        Reporting Live from somewhere near Kalamazoo

                        http://community.webshots.com/user/monte49002

                        Comment

                        • Mainemarc
                          Senior Member
                          • Nov 2003
                          • 673
                          • Portland, ME, USA.

                          #13
                          Very nice, Loring. Even if your version doesn't look strangely like one of Doc Oc's prehensile robotic arms, as does Rod's.
                          Marc

                          Comment

                          • lrogers
                            Veteran Member
                            • Dec 2002
                            • 3853
                            • Mobile, AL. USA.
                            • BT3000

                            #14
                            Great improvesments to an all ready great idea.
                            Larry R. Rogers
                            The Samurai Wood Butcher
                            http://splash54.multiply.com
                            http://community.webshots.com/user/splash54

                            Comment

                            • Tundra_Man
                              Veteran Member
                              • Jan 2003
                              • 1589
                              • Sioux Falls, SD, USA.
                              • Ryobi BT3100

                              #15
                              Looks like it works a lot better than my DP dust collection system, which are my shoes.
                              Terry

                              Life's too short to play an ordinary guitar: Tundra Man Custom Guitars

                              Comment

                              Working...