Hey you rust hunters

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • linear
    Senior Member
    • May 2004
    • 612
    • DeSoto, KS, USA.
    • Ryobi BT3100

    #1

    Hey you rust hunters

    I came up with this for the staggering sum of one dollar at a garage sale today.

    I can't quite place it other than it being a block plane. I don't find any Stanley markings or numbers on the casting, but the iron is a Stanley. Only thing readable on the casting is "MADE IN USA" on the heel. If I remove the iron there's "C-255" stamped in to the casting.

    Any ideas? It reminds me most of #61.



    Sorry for the phone picture.
    --Rob

    sigpic
  • linear
    Senior Member
    • May 2004
    • 612
    • DeSoto, KS, USA.
    • Ryobi BT3100

    #2
    On further consideration I like #220. I found the number 220 on the iron, and looking on the usual sites, they show a picture that looks like mine and list dimensions that are right on.

    http://www.supertool.com/StanleyBG/stan14.htm

    The lever cap is aluminum, and the body casting is 7" long.

    I don't think it's especially old. The knob looks like stained hardwood instead of rosewood. Machining looks so-so. But the casting is very nice.
    --Rob

    sigpic

    Comment

    • Hoakie
      Established Member
      • Feb 2007
      • 382
      • Iowa
      • Craftsman 21829

      #3
      I just picked one up off a CL deal (He had 5 planes for $30). So I over paid by 5$ . Also, mine has a different iron lock but other than that looks the same.


      Here is what I got:
      #220 Stanley block plane (cleaned nicely will compliment my low angle)
      #5 Stanley (chipper says 1867 but it is horribly pitted, same with iron, sole looks good so should be able to get replacement iron/chipper )
      #5 Stanley 1902 (will clean up nicely)
      #6? HS&B RenoVac (about 1" longer than the #5 Stanly's) corrugated bottom may not be salvageable (jagged opening behind iron)
      #4 HS&B RenoVac (good shape, will clean up nicely)

      I'll post pics when I get them cleaned up. I've used electrolysis to get rid if the rust. It was my first shot and I'm amazed at how easy it is and how well it does removing rust.
      Last edited by Hoakie; 09-21-2007, 10:36 AM. Reason: poor math skillz
      John
      To invent, you need a good imagination and a pile of junk. ~ Edison

      Comment

      • linear
        Senior Member
        • May 2004
        • 612
        • DeSoto, KS, USA.
        • Ryobi BT3100

        #4
        Since I'm only a dollar into this one, I decided to see what the old belt sander could do.

        The bottom was nowhere near flat, with the worst deficiencies around the mouth. So I took it down quite a ways beyond where it looked shiny to get a nice flat sole supporting the work right in front of and behind the mouth.

        The iron got the belt sander treatment too, it was super gnarly with chunks missing from the edge. I put a bevel on with the Veritas MkII honing jig and some sandpaper. Bevel looks like a mirror now.

        It's no Lie-Nielsen, but well worth the dollar plus about two hours effort spent in restoration (belt sander is the way to go!).


        The aluminum cap is dinged up pretty bad, but it's just the finish. Undoing the powder coating and painting it seemed like a bad choice, so I left it alone. Making a wooden cap would be a slick option.



        The sole flattened out nicely on the belt sander--it took about 20 minutes or so.



        It got shiny real fast, but I was after flattening out the area around the mouth. That took the other 19 minutes.



        It's hard to photograph a mirror, but this is my shot at showing you the mirror bevel on the iron.
        --Rob

        sigpic

        Comment

        • bthere
          Established Member
          • Jan 2007
          • 462
          • Alpharetta, GA

          #5
          Well, that looks a world different. So, how well does it work now with that mirror bevel edge?

          Comment

          • linear
            Senior Member
            • May 2004
            • 612
            • DeSoto, KS, USA.
            • Ryobi BT3100

            #6


            Those are some end grain mahogany shavings I just pulled. They read around .002 on the calipers I have. If I get them any thinner, they turn to sawdust when you touch them.

            So I'd say it's working pretty well.



            Added: here's an unresized shot for a grin

            Last edited by linear; 09-22-2007, 09:40 PM. Reason: added the closeup
            --Rob

            sigpic

            Comment

            • Hoakie
              Established Member
              • Feb 2007
              • 382
              • Iowa
              • Craftsman 21829

              #7
              What grit did you put on the belt sander? I have all the rust off 3 of the 5 and have done some sole-sanding but still not great or near flat. I don't wanna muss it up too bad. The two planes I purchased I was able to use 60-600 grit on glass, however they were pretty flat to start.

              Thanks
              John
              To invent, you need a good imagination and a pile of junk. ~ Edison

              Comment

              • linear
                Senior Member
                • May 2004
                • 612
                • DeSoto, KS, USA.
                • Ryobi BT3100

                #8
                120 grit. I'm using HF belts on a Delta 4" benchtop belt/disc sander.

                I did a #5 by hand, so I know what you're up against.

                Biggest tip--lift the casting off the belt with both hands. There's a strong tendency to drag one end and it will get rounded over. Luckily a rounded nose or tail doesn't affect performance too badly.

                I learned the real value of flattening around the mouth doing my #5.
                --Rob

                sigpic

                Comment

                Working...