Framing a mirror

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • lkazista
    Established Member
    • Jan 2004
    • 330
    • Nazareth, PA, USA.

    #1

    Framing a mirror

    OK-Needing help here for finishing off LOML xmas gifts.

    I am making here new accesories for the powder room, hanging magazine rack, towel holder, and a framed mirror. She has been talking about "buying" a set forever, so I figured I could make EXACTLY what I know she has been looking for.

    I am done with the Mag rack and towel bar, only the mirror left. I have a 24x30 mirror, and I picked up some 5/4 pine. I was thinking that I would just cut a dado slot through the center of the pine, thick enough to hold the mirror and a piece of 1/4 inch ply. I would just glue and pocket hole screw the whole thing together.

    Here is my issue. I started to rough cut the pieces today and EVERYTHING starting to warp on me, not a lot, but enough to concern me. My fear is now that the frame can twist and crack the mirror.

    Anyone have any experiance or even a clue as to how I should proceed?

    Thanks in advance, and enjoy the holidays.

    Lee Kazista
  • Uncle Cracker
    The Full Monte
    • May 2007
    • 7091
    • Sunshine State
    • BT3000

    #2
    That could very well happen. Pine does warp. A lot. In a bathroom where steam will be present, maybe even more. Probably not the best wood choice. No matter which wood you end up using, it must be completely sealed against moisture. A few coats of spar urethane will probably work best. Be aware that this finish is not totally colorless. Set the frame up so that the mirror is not attached in so many places, so that if warpage does occur, there will be some give, so that the frame can go its merry way without taking the mirror with it. Rather than a slot in the frame to retain the mirror and its backing, you should think about a rabbet, open to the rear of the frame. Then just pin the mirror backing in place in a few spots.
    Last edited by Uncle Cracker; 12-21-2007, 08:48 PM.

    Comment

    • leehljp
      The Full Monte
      • Dec 2002
      • 8804
      • Tunica, MS
      • BT3000/3100

      #3
      For mirror and picture frames, kiln dried wood is a necessity. Most of the time now, that kind of wood is available only at specialty stores. Most HD and Lowes do have oak, poplar and maybe another, but by and large, pine from those are not dried to the content for furniture making.

      I don't know if you did this or not, but learning to spot good wood and what might and might not warp is very helpful. Pass over knotted wood, grain that is not straight top to bottom, end to end, edge to edge. Take each board and look at it - eyeballing it down the length. Look for bow, curve or twist, even minutely and eliminate it. Compare each board until you have enough. I usually go through much more than I need and then compare to get the best of the best.

      On occasion, I don't have a choice but to get wood with some knots in it, but I still compare the grain in the manner mentioned above and come out OK on the finished product. You can get lots of straight and flat boards with irregular grain. Beware of these as they are the ones more likely to warp or twist over time when cut, dadoed or grooved.

      95% of the time, I do not have a problem that you are having simply by having chosen the right board. It does matter which board you choose. If good grain is not available, I put my project off until I can check with other places and get the right wood, i.e. fairly straight grained end to end, top to bottom, edge to edge without warp or twist.
      Last edited by leehljp; 12-21-2007, 09:20 PM.
      Hank Lee

      Experience is what you get when you don't get what you wanted!

      Comment

      • Slik Geek
        Senior Member
        • Dec 2006
        • 708
        • Lake County, Illinois
        • Ryobi BT-3000

        #4
        Buy your wood weeks in advance and "sticker" it. (Stack the boards with sticks or strips of wood carefully spaced between each board - and place weights on top to keep the wood in the proper position.) This will allow the wood's moisture level to equalize to your home's humidity level.

        The wood you get at the store may seem dry, but for the sake of reduced costs, they minimize the space required and dry the minimum time that they can get away with. If you have chosen stable grain patterns, and the wood is at equilibrium (because you stickered it), the movement problem you have had will be significantly reduced.

        Below is a photo of treated lumber that I stickered. (This type of wood is often very wet). I do this with all wood that I get.

        Comment

        • lkazista
          Established Member
          • Jan 2004
          • 330
          • Nazareth, PA, USA.

          #5
          Everyone_

          Thank you for the tips. Although the 5/4 is Pine, is was Kiln Dried. Picked it up at my local lumber yard. The guy that works there is great and picks through boards for me all of the time. He has a private stash that he keeps for people looking for only a couple of boards for projects versus builders. This board has ZERO knots and fairly tight grain.

          BUT - I did buy it yesterday and start to rough cut last night. I guess that was my error.

          Any thing that I can do now? Run it through the planer? Or should I just start glueing some pre primed FG Pine together to get my thickness, and go that route, saving this 5/4 for some "other" project?

          Thanks again guys.

          Lee

          Comment

          • Slik Geek
            Senior Member
            • Dec 2006
            • 708
            • Lake County, Illinois
            • Ryobi BT-3000

            #6
            Did the warping occur almost immediately after cutting? Or did it take hours?

            If it happened immediately, then there likely was "reaction wood" that was released to "do its thing" when the boards were cut.

            Is it possible to post a photo of an entire board plus a closeup of the grain pattern? That would help the forum to analyze your situation better.

            Comment

            • JimD
              Veteran Member
              • Feb 2003
              • 4187
              • Lexington, SC.

              #7
              I agree with the reaction wood comment.

              I've made a few mirror frames including one from softwood - the cheap stuff from the lumber yard - and none of the mirrors cracked. The pine frame warped but the mirror flexed with it and did not break. Maybe I've been lucky.

              I like to put a double rabbet if the frame is thick enough. The deeper rabbit is for the mirror and the backer piece. I can get door skin plywood which is only about 1/8 thick which can help. Outside this is a rabbet for a flat piece that overlaps the mirror and backer. The flat piece is bradded into the mirror frame but the backer and mirror just floats in the rabbet pinned in place by the flat piece.

              The last mirror I did this way has a 5/4 maple frame and the inner edge around the mirror has an ogee profile. It is the front of a built-in jewelry chest (which is recessed into the wall).

              Jim

              Comment

              Working...