Removing Stain??

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • Wood_workur
    Veteran Member
    • Aug 2005
    • 1914
    • Ohio
    • Ryobi bt3100-1

    #1

    Removing Stain??

    what is the best method. I have a night stand I got a garage sale when I was 5, and I am trying to refinish it natural (or even a rustic kid of look) it is yellow pine, and was stained a dark brown. I have tried kutz-it, but that didn't do it, and laundry bleach didn't do it either. The only other methods I've heard of are hydrogen peroxide in the sun or Oxalic acid. What is the best way to get it down to a natural color?
    Alex
  • Uncle Cracker
    The Full Monte
    • May 2007
    • 7091
    • Sunshine State
    • BT3000

    #2
    Sandpaper... Lots and lots of sandpaper...

    Comment

    • Pappy
      The Full Monte
      • Dec 2002
      • 10490
      • San Marcos, TX, USA.
      • BT3000 (x2)

      #3
      Lowe's sell a stain remover under the Jasco brand that is fairly effective. Like Unc says, you are still going to need lots of sandpaper!
      Last edited by Pappy; 10-29-2007, 04:44 AM.
      Don, aka Pappy,

      Wise men talk because they have something to say,
      Fools because they have to say something.
      Plato

      Comment

      • cabinetman
        Gone but not Forgotten RIP
        • Jun 2006
        • 15216
        • So. Florida
        • Delta

        #4
        I would try some stripper before I used any sandpaper. If you have to use it inside, try Citra Strip, it's a non MC based stripper that smells like oranges, and cleans up with water. Or, if you use an MC based stripper, do it outside with good ventilation. You may need several applications. You should wear gloves for either.

        Comment

        • crokett
          The Full Monte
          • Jan 2003
          • 10627
          • Mebane, NC, USA.
          • Ryobi BT3000

          #5
          Sandpaper has always worked for me. Every time I've tried using a stain remover I ended up sanding anyway. Now I just skip the stain remover and go to the sanding. Use a coarser grit - 120 or 150 to remove the stain. Anything above 150 will load up quickly and you will burn through more paper.
          David

          The chief cause of failure in this life is giving up what you want most for what you want at the moment.

          Comment

          • cabinetman
            Gone but not Forgotten RIP
            • Jun 2006
            • 15216
            • So. Florida
            • Delta

            #6
            Originally posted by crokett
            Sandpaper has always worked for me. Every time I've tried using a stain remover I ended up sanding anyway. Now I just skip the stain remover and go to the sanding. Use a coarser grit - 120 or 150 to remove the stain. Anything above 150 will load up quickly and you will burn through more paper.

            This may not apply to this specific case, but if the furniture is a veneer (sometimes it's hard to tell), it's possible to sand through the veneer before you know it.

            Comment

            • crokett
              The Full Monte
              • Jan 2003
              • 10627
              • Mebane, NC, USA.
              • Ryobi BT3000

              #7
              Originally posted by cabinetman
              This may not apply to this specific case, but if the furniture is a veneer (sometimes it's hard to tell), it's possible to sand through the veneer before you know it.
              True - but then you've sanded the stain off, which is what you wanted, right?

              Seriously, Cabinetman has a good point. check to see if the furniture is a veneer before you start sanding.
              David

              The chief cause of failure in this life is giving up what you want most for what you want at the moment.

              Comment

              Working...