Swelling MDF

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • steve-norrell
    Veteran Member
    • Apr 2006
    • 1001
    • The Great Land - Alaska
    • BT3100-1

    #1

    Swelling MDF

    I am using 3/4 inch MDF to build the carcasses of garage/workshop cabinets. Mostly, they are relatively simple boxes, but a couple have shelves made of MDF across the middle, in dados cut into the side panels. I believe this adds rigidity and some strength to the cabinets. I dry assemble them and they usually go together without a problem; the dados are tight, but the shelf can be inserted with just hand pressure.

    The problem comes when I apply glue (Titebond II) to the dados and try to insert the shelf into the dado. They simply will not go, even when using a mallet to beat the other end shelf. I know that MDF has some tendency to swell when wet but I have had swelling to the point that I could not get the shelf to seat completely to the bottom of the dado.

    I have gotten around the couple of problems so far by keeping my handy sander nearby, but I worry that this will result in a loose fit and I am not sure this is a good long term solution.

    Is there any kind of rule of thumb that I could use to take this into account?

    Regards, Steve
  • cabinetman
    Gone but not Forgotten RIP
    • Jun 2006
    • 15216
    • So. Florida
    • Delta

    #2
    The dry fit should slip with very little friction. The panel should go in with just hand pressure, and no tapping. You may be applying too much glue, which would cause a binding, and keeping the panel from seating. I usually just brush the glue into the dado with no globs, and very lightly coat the very end edge of the panel. The initial "tack" will cause it to stick if the dry fit had too much resistance. I keep a hand block sander handy to dress the edge of the panel when doing the "dry fit".
    .

    Comment

    • cgallery
      Veteran Member
      • Sep 2004
      • 4503
      • Milwaukee, WI
      • BT3K

      #3
      How do you apply the glue? Do you leave it in a bead or do you spread it out?

      I noticed that Nahm often throws two beads of glue in the bottom of the grove, one along each edge. He doesn't spread it out, but just slides the components together, then clamps.

      While not optimum for glue distribution, it certainly does help when trying to assemble tight components.

      Nahm's method can also create hydraulic problems, so avoid using too much glue and have plenty of clamps on hand.

      Comment

      • steve-norrell
        Veteran Member
        • Apr 2006
        • 1001
        • The Great Land - Alaska
        • BT3100-1

        #4
        Cabinetman and cgallery: Thanks for the reply. I believe you are right.

        I use a brush and try to get glue on all surfaces (bottom and both sides of a dado). I tend to be generous with the glue and typically have to spend some time wiping off the excess that oozes out of the joint. It sounds like I should just put a thin layer of glue on the bottom surface only.

        Thanks for the suggestions. Regards, Steve.

        Comment

        • steve-norrell
          Veteran Member
          • Apr 2006
          • 1001
          • The Great Land - Alaska
          • BT3100-1

          #5
          Originally posted by cgallery
          I noticed that Nahm often throws two beads of glue in the bottom of the grove, one along each edge. He doesn't spread it out, but just slides the components together, then clamps. . .
          . . . so avoid using too much glue and have plenty of clamps on hand.
          . . . and . . .

          Originally posted by cabinetman
          The dry fit should slip with very little friction. The panel should go in with just hand pressure, and no tapping. You may be applying too much glue, which would cause a binding, and keeping the panel from seating. I usually just brush the glue into the dado with no globs, and very lightly coat the very end edge of the panel.
          Thanks for the suggestions. I assembled a new cabinet and applied a thin coat of glue to only the bottom of the dado as suggested in your comments. Everything went together with a little bit of sanding and only minor hand tapping

          I had been careful to make sure that all mating surfaces were coated with glue, sometimes more generously than needed. That is clearly not the way to go with tight dados.

          Again, thanks for the suggestions.

          Regards, Steve

          Comment

          Working...