Postformed countertop

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • Salty
    Senior Member
    • Feb 2006
    • 690
    • Akron, Ohio

    #1

    Postformed countertop

    Hello all. I got 2 small sections of countertop made at the blue box and am close to setting them. Question is, should I seal the underside of countertops?
    I don't see that they put anything on the under side of the particle board. I know the better manufacturers use a paper backing to balance the substrate.
    Maybe just some polyurethane?
    Why doesn't the word 'planing' show up in my computer spell check?
  • cabinetman
    Gone but not Forgotten RIP
    • Jun 2006
    • 15216
    • So. Florida
    • Delta

    #2
    Originally posted by Salty
    Hello all. I got 2 small sections of countertop made at the blue box and am close to setting them. Question is, should I seal the underside of countertops?
    I don't see that they put anything on the under side of the particle board. I know the better manufacturers use a paper backing to balance the substrate.
    Maybe just some polyurethane?

    Most counter tops are constructed with a build up edge in the front and back. The build ups and/or curves adds significant rigidity to the longitudinal integrity of the tops. When installed they are screwed down front and back. It would not be necessary to laminate, or seal the backside. The possibility exists that warping could happen even if sealed.

    If this was a single layer of substrate, like a shelf, a backer would be advised. If not sealing the backs will cause sleepless nights, great weight loss or gain, loss of employment, eventual bankruptcy, family breakups, flat tires, indigestion, impotency, athletes foot, or loss of memory, by all means, seal the back.
    .

    Comment

    • Salty
      Senior Member
      • Feb 2006
      • 690
      • Akron, Ohio

      #3
      Thank you Cabinetman.
      I installed them yesterday and all went well. I did not do anything to the underside. There is a built-up border around the perimiter as you said. I didn't screw them down, just used spots of construction adhesive. I thought about using screws but there is only a 1/8" thick piece of plywood in the corners and I didn't think that would do much good.
      Also, I lucked out on the style choice. We got a bullnose front which shortened the backsplash height to 3" insted of 4". The old backslpash was 3" too so I did not have to cut the tile or just butt it up aginst the tile. Neither of those methods would have looked good.
      Now I can look forward to doing the 11-1/2 foot run on the other side of the kitchen!
      Why doesn't the word 'planing' show up in my computer spell check?

      Comment

      • cabinetman
        Gone but not Forgotten RIP
        • Jun 2006
        • 15216
        • So. Florida
        • Delta

        #4
        Originally posted by Salty
        There is a built-up border around the perimiter as you said. I didn't screw them down, just used spots of construction adhesive. I thought about using screws but there is only a 1/8" thick piece of plywood in the corners and I didn't think that would do much good.

        If your cabinets have a front and back rail, you could drill a pilot hole through and use a long screw to fasten down the top. If you do that, countersink the heads, especially under the front rail. If you don't have rails (there has to be something there, even the top rail to the faceframe), add one, preferrably 90 degrees to the backside of whatever is there. You may have to cut a clearance for the front of the sink. These add-ons should be 3/4" either solid wood or plywood, and they will also stiffin up the upper sections of base cabinets.

        If all there is in the corners is an 1/8" gusset, add a 3/4" gusset under. It's much better to screw down the tops than to use construction adhesive, even though the adhesive will keep the top from moving around.

        When removing a top that has been secured with just an adhesive, there is more of a possibility of doing damage to the cabinets than when screws are used, IMO.
        .

        Comment

        • Salty
          Senior Member
          • Feb 2006
          • 690
          • Akron, Ohio

          #5
          Good advise as always Cabinetman.
          I think I'll put those suggestions to work when I tackle the long countertop.
          Why doesn't the word 'planing' show up in my computer spell check?

          Comment

          Working...