Straight Edge ?!?

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • footprintsinconc
    Veteran Member
    • Nov 2006
    • 1759
    • Roseville (Sacramento), CA
    • BT3100

    #1

    Straight Edge ?!?

    My work bench is 9ft long. for edging around the perimeter of the table top, i plan on using 3/4"thick x 2.5" tall hard maple.

    before this all i straight edged was 6ft long oak using 1/2" x 4" straight edge attached to the oak using the aluminum 'C' shaped extruded shapes (from rockler) on the table saw.

    Now, i dont know how to straight edge this 10ft long board. i tried to chaulk a line and then use the 6" jointer to get rid of the hight spots on the ends. the board is too long to keep on the short bed straight.

    What and how should or can i do to get a striaght edge so that i can rip 2.5" strips on the table saw? Any tricks?

    your help is greatly appreciated --- thanks!
    _________________________
    omar
  • cabinetman
    Gone but not Forgotten RIP
    • Jun 2006
    • 15216
    • So. Florida
    • Delta

    #2
    I keep an 8' long piece of 1/2" x 8" wide plywood that has been straight edged on the TS. IOW, it has two straight edges, that are parallel to each other. You lay the ply on top of the 10' board (put the worst side up) and allow a long edge to be cut off on the left side. The right edge of the ply rides against the fence. Now, this is the part you may not like. Use small finish nails (4) through the ply into the backside of the subject board to hold the two together.

    If your subject board is 10' and the guide board is 8', you'll have 1' of lead on the ends. If you have an infeed and outfeed support (which you should have), you can smoothly feed the two through.

    This will work with boards that have drastically uneven edges by sighting a line to mount the guide board. I also keep a 10' piece that was a cutoff from a 4'x10' sheet of plywood for exactly this reason. Jointing very long boards 10' - 20' is very difficult on a jointer, especially for those with minimal experience, and working alone.

    Rockler has a jointer jig for the table saw that might help solve your problem.
    http://www.rockler.com/product.cfm?page=6415
    .
    .

    Comment

    • pecker
      Established Member
      • Jun 2003
      • 388
      • .

      #3
      Originally posted by cabinetman
      I keep an 8' long piece of 1/2" x 8" wide plywood that has been straight edged on the TS. IOW, it has two straight edges, that are parallel to each other. You lay the ply on top of the 10' board (put the worst side up) and allow a long edge to be cut off on the left side. The right edge of the ply rides against the fence. Now, this is the part you may not like. Use small finish nails (4) through the ply into the backside of the subject board to hold the two together.

      If your subject board is 10' and the guide board is 8', you'll have 1' of lead on the ends. If you have an infeed and outfeed support (which you should have), you can smoothly feed the two through.

      This will work with boards that have drastically uneven edges by sighting a line to mount the guide board. I also keep a 10' piece that was a cutoff from a 4'x10' sheet of plywood for exactly this reason. Jointing very long boards 10' - 20' is very difficult on a jointer, especially for those with minimal experience, and working alone.

      Rockler has a jointer jig for the table saw that might help solve your problem.
      http://www.rockler.com/product.cfm?page=6415
      .
      .


      You can also sometimes just use hot melt glue to hold the straight ply to the workpiece. They can be pried apart afterward, and the glue peels off pretty easy.

      Comment

      • footprintsinconc
        Veteran Member
        • Nov 2006
        • 1759
        • Roseville (Sacramento), CA
        • BT3100

        #4
        thanks for the advice.

        cabinetman, i am now working on getting a 10' long board that i will keep around. those are the clamps that i have.

        thanks once again.
        _________________________
        omar

        Comment

        • ragswl4
          Veteran Member
          • Jan 2007
          • 1559
          • Winchester, Ca
          • C-Man 22114

          #5
          Originally posted by cabinetman
          I keep an 8' long piece of 1/2" x 8" wide plywood that has been straight edged on the TS. IOW, it has two straight edges, that are parallel to each other. You lay the ply on top of the 10' board (put the worst side up) and allow a long edge to be cut off on the left side. The right edge of the ply rides against the fence. Now, this is the part you may not like. Use small finish nails (4) through the ply into the backside of the subject board to hold the two together.

          If your subject board is 10' and the guide board is 8', you'll have 1' of lead on the ends. If you have an infeed and outfeed support (which you should have), you can smoothly feed the two through.

          This will work with boards that have drastically uneven edges by sighting a line to mount the guide board. I also keep a 10' piece that was a cutoff from a 4'x10' sheet of plywood for exactly this reason. Jointing very long boards 10' - 20' is very difficult on a jointer, especially for those with minimal experience, and working alone.

          Rockler has a jointer jig for the table saw that might help solve your problem.
          http://www.rockler.com/product.cfm?page=6415
          .
          .
          I made one of those using two hold down clamps from Grizzly.com. I used 1/2" mdf as the base, screwed and glued a piece of 3/4" oak along one long edge of the mdf and attached the clamps to the oak about 6" from each end.
          The clamps are available in various places. Works great for longer boards. Just be sure to use infeed/outfeed support as suggested. A helper would be nice.
          RAGS
          Raggy and Me in San Felipe
          sigpic

          Comment

          Working...