How to carry 4x8' on PT cruiser top?

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • gychang
    Established Member
    • Jan 2006
    • 188
    • Sacramento, California
    • none

    #1

    How to carry 4x8' on PT cruiser top?

    I have a roof rack but somewhat curved (original accessory) on my 2001PT cruiser.

    Love the car, anyone have experience whether I can carry 4x8' plywood panel?

    thanks,

    gychang
  • crokett
    The Full Monte
    • Jan 2003
    • 10627
    • Mebane, NC, USA.
    • Ryobi BT3000

    #2
    I would get a trailer. Or pay the 20 bucks for the BORG rental truck before I tied a 4x8 sheet of plywood to ANY car. Either the trailer, truck or have them cut it into pieces that fit inside the car.
    David

    The chief cause of failure in this life is giving up what you want most for what you want at the moment.

    Comment

    • Cheeky
      Senior Member
      • Nov 2006
      • 862
      • westchester cty, new york
      • Ridgid TS2400LS

      #3
      Thule Roof rack:

      430 Tracker II Foot Pack | LB50 Load Bars | TK1 Tracker Kit

      or

      430R Rapid Tracker | RB43 Rapid Load Bars | TK1 Tracker Kit

      fits into the factory rails on your car. the load bars will be steel and straight.

      check the weight limit from Chrysler, you should be able to transport at least a couple sheets (believe my Civic's weight limit is over 125lbs).

      with cam straps, i'm out of the parking lot in about 7 minutes.
      Pete

      Comment

      • cabinetman
        Gone but not Forgotten RIP
        • Jun 2006
        • 15216
        • So. Florida
        • Delta

        #4
        A trailer would be the easiest and safest way. HF has this folding trailer, if you're interested.

        If you prefer to make something to improve your roof rack, one of our members "aiyou" sent me this:
        .

        Comment

        • gychang
          Established Member
          • Jan 2006
          • 188
          • Sacramento, California
          • none

          #5
          Originally posted by cabinetman
          A trailer would be the easiest and safest way. HF has this folding trailer, if you're interested.

          If you prefer to make something to improve your roof rack, one of our members "aiyou" sent me this:
          .
          thanks, this is what I was looking for, great tip.

          gychang

          Comment

          • messmaker
            Veteran Member
            • May 2004
            • 1495
            • RICHMOND, KY, USA.
            • Ridgid 2424

            #6
            Sheet goods can catch a lot of air as your speed increases. It is easy to underestimate how much it takes to secure your load well enough to hold it in place.
            spellling champion Lexington region 1982

            Comment

            • kramer katt
              Established Member
              • Aug 2004
              • 375
              • SO CAL, USA
              • BT3100 and Craftsman 100

              #7
              Remembering back to how much uplift a piece of 4'' abs pipe tugged on my arm that I was trying to carry resting on the side mirrors at only 30 mph I cringe at thinking at what a sheet of plywood could do. Also I bet the manufactur's rating in the manual only lists the dead load on those factory racks and not an uplifting force. Anyway a 25 LB sheet of plywood may actually be uplifted by a couple hundred pounds due to wind.
              Last edited by kramer katt; 01-20-2008, 02:10 AM.
              Everything should be made as simple as possible, but not simpler
              --Albert Einstein

              Comment

              Working...