What Else Can Go Wrong - & a Question

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • MilDoc

    #1

    What Else Can Go Wrong - & a Question

    Took Friday off, planned to get some shop time. Then I saw some water leakage onto the entry hall floor, and it soaked the coat closet carpet. Could only be from one source - the HVAC unit in its own closet right next to it. Yep. Blocked drainage tube. OK. No problem. Just clear it out.

    Right. Should have been a friction fit but I couldn't get it loose. OK. Hook up the ShopVac to the drainage tube outside. Try to "suck" it clean. No dice.

    2 hours later gave up. Called an air conditioner guy. He couldn't loosen the indoor connection either, but was able to get to the internal connection and blow it out (cool tool!). Then hooked his ShopVac to the outside and finally got it clear. Only got an hour in the shop.

    OK. Saturday. Yard work done, decided the car hadn't been washed in months thanks to all the rain we've had. Cleaned and Armor All'ed the inside. Washed it good. Took it into the garage and gave it a good wax coat.

    Now, shop time. Hit the garage door button. Door went half-way down, then ... BANG! I knew that sound. Disconnected the opener. Door slammed closed.

    Yep. Busted spring. Waited an hour to get a guy out to replace both springs. Very interesting watching him do it. Still not sure I'd ever want to do it myself (too dangerous).

    Only 2 hours shop time today. What a weekend!

    OK. Now the question. The garage door guy said to lubricate the new springs every 3 months or so with motor oil. I'd been using WD40 which he said dried out too fast.

    Motor oil sounds fine, but awful messy. I assume his advice is good, but any suggestions on just how to do that without making a real mess???
  • Thom2
    Resident BT3Central Research Ass.
    • Jan 2003
    • 1786
    • Stevens, PA, USA.
    • Craftsman 22124

    #2
    Personally, I've never lubricated a garage door spring and have only over seen 1 fail ... if you insist that you need to do this with motor oil then I'd consider one of the oil guns




    $3.99 at HF
    If it ain't broke.. don't fix it!!!... but you can always 'hop it up'
    **one and only purchaser of a BT3C official thong**

    Comment

    • Thalermade
      Senior Member
      • Dec 2002
      • 791
      • Ohio
      • BT 3000

      #3
      When I had a garage door opener repair and adjustment last winter, the repairmen said he used a 50/50 mix of auto oil and WD-40 (that he mixed in in a regular spray bottle) to lubricate the springs.

      Get some old rags and lay under the spring and squirt away.

      Russ

      Comment

      • cabinetman
        Gone but not Forgotten RIP
        • Jun 2006
        • 15216
        • So. Florida
        • Delta

        #4
        My largest shop had 6 segmented wood doors, the largest being 12' x 12'. Only twice did I have to work on springs, and both times it was to adjust the tension. Those springs are huge and extremely dangerous to work on. Needed a long bar, wrench, and 3 hands, while standing on a tall ladder. With the springs disabled, the door cannot be lifted by hand, or hands. DAMHITK.

        I've never oiled springs, never heard that suggestion even after having a repair guy replace a spring. But, if oiling is your thing, maybe try one of those hand pump garden sprayers, and thin the oil if it doesn't atomize. Take the suggestion to cover the area behind and below the spring. Maybe you should have asked your repairman the best method for homeowners. They probably have a cute little kit in a folding briefcase for $89.95.

        Comment

        • Stytooner
          Roll Tide RIP Lee
          • Dec 2002
          • 4301
          • Robertsdale, AL, USA.
          • BT3100

          #5
          You can get chain lube like on a bicycle. I personally haven't ever lubed springs, but have seen it done. Not so much to prevent failure, as to reduce noise and rust dust on the garage floor.
          I use graphite spray. It goes on like spray paint and will prevent rusting, noise and most likely friction failure as was probably this case. It is some good stuff. It dries and doesn't catch dust and things on it either.
          To get enough oil on there to do a good job would really be messy.
          Lee

          Comment

          • cgallery
            Veteran Member
            • Sep 2004
            • 4503
            • Milwaukee, WI
            • BT3K

            #6
            Silicone spray would be better on the springs than WD-40. Although I never lubricate my springs, it does seem like an obvious thing to do to prolong their life now that you mention it.

            Comment

            • Ed62
              The Full Monte
              • Oct 2006
              • 6021
              • NW Indiana
              • BT3K

              #7
              My "garage door opener guy", a pro, told me to use WD-40. Silicone spray sounds good to me too.

              Ed
              Do you know about kickback? Ray has a good writeup here... https://www.sawdustzone.org/articles...mare-explained

              For a kickback demonstration video http://www.metacafe.com/watch/910584...demonstration/

              Comment

              • Daryl
                Senior Member
                • May 2004
                • 831
                • .

                #8
                WD-40 dries to a varnish like substance. If you just squirt a bead of oil across the top of the coil capilary action will get it down between the coils.
                Sometimes the old man passed out and left the am radio on so I got to hear the oldie songs and current event kind of things

                Comment

                • jackellis
                  Veteran Member
                  • Nov 2003
                  • 2638
                  • Tahoe City, CA, USA.
                  • BT3100

                  #9
                  I've never had a problem with broken springs bit I did replace one bearing in our single piece door. They're (2 of them) by the sides of the door instead of up near the track the opener rides on.

                  However, you do need to lubricate the track and wheels either side of the door. I use white grease. Otherwise, the wheels on one side may not slide or roll very well, and that can cause all sorts of problems.

                  Eventually we'll replace our door with a segmented version.

                  Comment

                  • MilDoc

                    #10
                    Thanks for the suggestions.

                    Comment

                    • Russianwolf
                      Veteran Member
                      • Jan 2004
                      • 3152
                      • Martinsburg, WV, USA.
                      • One of them there Toy saws

                      #11
                      guy that just replaced ours said to use WD40, said it will slow down the rust and get a couple extra years out of them, But eventually they will break again. Metal fatigue.

                      He also recommended (on wooden doors) to check/tighten the bolts on the hinges that connect the panels as they may work loose over time.
                      Mike
                      Lakota's Dad

                      If at first you don't succeed, deny you were trying in the first place.

                      Comment

                      • mater
                        Veteran Member
                        • Jan 2004
                        • 4197
                        • SC, USA.

                        #12
                        I hope this weekend is a better one for you.
                        Ken aka "mater"

                        " People may doubt what you say but they will never doubt what you do "

                        Ken's Den

                        Comment

                        Working...