"Wearing" Tools In The Shop

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • LarryG
    The Full Monte
    • May 2004
    • 6693
    • Off The Back
    • Powermatic PM2000, BT3100-1

    #1

    "Wearing" Tools In The Shop

    Chalk up this question mostly to idle curiosity, albeit with a minor in "always looking for a better way."

    I spent a few years working as a carpenter, so when I'm in the shop I keep essential tools on my person by wearing a set of leather nail bags, ala Nahm, because that's what I'm used to. I thought about a long cloth apron, but feared it might be too hot in my un-air-conditioned shop.

    To keep the weight down, I try to carry only the stuff I use a lot: 16' tape, 6" rule, 6" double square, saddle square, utility knife, X-Acto knife, common screwdriver, Phillips screwdriver, Japanese awl, pencil, chalk, small hammer. I generally don't carry any nails, screws, or biscuits, but keep a pocket empty for these when I need to.

    I've noticed that David Marks doesn't use anything on WoodWorks, but maybe that's just for TV.

    What does everyone else do? Advantages, drawbacks, etc?
    Larry
  • kwgeorge
    Veteran Member
    • Jan 2004
    • 1419
    • Alvin, TX, USA.

    #2
    I personaly don't wear any tools in the shop. Everything is pretty much in reaching distance.

    Comment

    • RainShadow
      Established Member
      • Dec 2002
      • 392
      • Oceanside, CA, USA.

      #3
      I actually do not wear anything at all except a baseball cup -----
      just kidding. Sometimes I wear my carpenters belt when I am putting things together; but for the most part only my tape measure and pencil.
      Have a GREAT weekend , Randy from Oceanside, CA

      Comment

      • JR
        The Full Monte
        • Feb 2004
        • 5636
        • Eugene, OR
        • BT3000

        #4
        I'm an apron guy ($2 at HF!). Three pockets.

        I try to keep only the tools I'll be using right now in the pockets. That means always a tape measure, a square and a pencil. No hammer, screwdrivers only if I'll need it. I found that I had so much stuff in there it was pulling the apron uncomfortably on my neck.

        My mission is to make hand tools so readily available that the few steps to retrieve them is not onerous. Of course the implication is that I'll put my tools away - but I'll save that confession for another day.

        JR
        JR

        Comment

        • Otter
          Senior Member
          • Nov 2003
          • 865
          • Cumming, GA, USA.
          • Delta Left Tilt UniSaw

          #5
          a pencil, 6" ruler, Vernier calipers, coffie mug (caped with attached coaster), cell phone (just in case I try to remove the thumb again), Leatherman.
          All men dream, but not equally. Those who dream by night in the dusty recesses of their minds wake in the day to find that it was vanity: but the dreamers of the day are dangerous men, for they may act their dream with open eyes, to make it possible

          T.E. Lawrence

          Comment

          • jnesmith
            Senior Member
            • Jan 2003
            • 892
            • Tallahassee, FL, USA.

            #6
            I don't carry any, but, like you, have thought about various options.

            I don't think I'm going to go with an apron or large tool belt either, also because no AC.

            The one item I would most like to have constantly at my fingertips is a mechanical pencil. I thought buying a dozen and scattering them around the shop would take care of it, but it hasn't. I need one on my person.
            John

            Comment

            • Rounder
              Veteran Member
              • Jan 2003
              • 1287
              • Sanford, FL, USA.
              • BT3100

              #7
              I tried the apron thing, but it seemed to get in the way. I have a pair of pants and a pair of shorts with cargo pockets on them. Depending on the project I will wear one or the other.

              In the pockets, As far as tools, I keep a tape measure, drafting pencil, the marking gauge from Incra (grey plastic forgot what it is called), a switchblade (or other knife that can be opened one handed), and maybe a speed square.

              As far as non-tools, I carry a cell phone and a pistol. My shop is at the back of the property and borders on the alley. We get lots of foot traffic thru the alley at night and some of it is undesirable. For ventialtion, I have to keep the doors open that lead to the alley.
              George AKA Rounder

              "Amarillo Slim, the greatist proposition gambler of all time held to his father's maxim; You can shear a sheep many times, but you can skin him only once."

              Comment

              • SteveR
                Established Member
                • Feb 2003
                • 494
                • USA.

                #8
                Ex-carpenter here too.....hard to get away from old habits. It depends on what I am working on....maybe 50/50 now....now that shop is getting more organized, I find I do not need the bags as often. And sometimes they just get in the way, but I'll never get rid of them.
                Steve

                Comment

                • WEG
                  Established Member
                  • Nov 2003
                  • 298
                  • Nahant, MA.

                  #9
                  This is the best thread in a long time. Thanks guys!

                  Great idea Rounder, pack a pistol...but I also pack a cell phone in case I shoot my thumb off

                  Oh, I just leave my stuff all over the work benck or on the floor depending where the project is. Those tool belts just keep pulling my pants down...but my baseball cup takes over when that happens
                  One can't be too safe...you never know when you will get a foul tip from the saw! Ouch Ouch [:0]

                  Keep the fun coming!

                  WEG

                  Comment

                  • Ken Weaver
                    Veteran Member
                    • Feb 2004
                    • 2417
                    • Clemson, SC, USA
                    • Rigid TS3650

                    #10
                    Sometimes I use an apron, but mostly nothing. With the tool tray in my workbench, things are never far away.
                    Ken Weaver
                    Clemson, SC

                    "A mistake is absolute proof that someone tried to do something!

                    Comment

                    • gerti
                      Veteran Member
                      • Dec 2003
                      • 2233
                      • Minnetonka, MN, USA.
                      • BT3100 "Frankensaw"

                      #11
                      Tool belts are handy. When I use it I load it with the most used tools for the job at hand. Often when I don't use it I miss it, it is darn handy to be able to just reach down without looking and find the pencil, knife, tape etc.

                      Gerd

                      Comment

                      • John Hunter
                        Veteran Member
                        • Dec 2004
                        • 2034
                        • Lake Station, IN, USA.
                        • BT3000 & BT3100

                        #12
                        Just a tape measure and a pencil.
                        John Hunter

                        Comment

                        • rabmaxx
                          Established Member
                          • Aug 2004
                          • 150
                          • Henderson, Nevada.

                          #13
                          I have a denim medium weight apron from Woodsmith which was fine in the winter but I thought too warm in the summer. Until a small but high speed piece of wood slashed across the side of my soft stomache but not quite through the apron.

                          Not much else because it is too easy for somwthing to get caught, snarled, grabbed, torn, ripped or--well you ge the ideaa.


                          Ron

                          Comment

                          • RayintheUK
                            Veteran Member
                            • Sep 2003
                            • 1792
                            • Crowborough, East Sussex, United Kingdom.
                            • Ryobi BT3000

                            #14
                            The only thing I "wear" when working is a steel tape measure, clipped to my belt. I've tried hanging other stuff off my belt, but didn't like it. Most stuff is right to hand anyway and I know where everything is, so that's how I operate in the shop.

                            When I'm away from the shop I use my old faithful Posso T-Box 400 that I've had since 1979. I don't think you can get them over here any more, but I wouldn't be without mine, it's great.

                            Ray.
                            Did I offend you? Click here.

                            Comment

                            • Popeye
                              Veteran Member
                              • Mar 2003
                              • 1848
                              • Woodbine, Ga
                              • Grizzly 1023SL

                              #15
                              I'm a bib shop apron kinda guy. I've got at least 4 tapes in the shop and without apron pockets I'd never be able to find one.
                              Plus I carry pencils, 6" rule, fat eraser.
                              And let's not forget......gotta have someplace to wipe excess glue besides my jeans and the underside of shop tables [B)][B)] Pat
                              Woodworking is therapy.....some of us need more therapy than others. <ZERO>

                              Comment

                              Working...