How to make louverd panels

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • BryanRabb
    Forum Newbie
    • Sep 2004
    • 20
    • Fort Mill, SC, USA.

    #1

    How to make louverd panels

    I have undertaken a project that I wish I hadn't. I am building a wet bar, but instead of raised panels on the front, this guy wants louvered panels so he can back light them. If he wasn't one of my closest friends I would send him packing. I need help/advice relating to making these. I have no idea where to start. However, I do remember Norm making a jig to rout the groves to recieve the slats. Any advice is welcome.

    Thanks.
    When in doubt, cut long.
  • LarryG
    The Full Monte
    • May 2004
    • 6693
    • Off The Back
    • Powermatic PM2000, BT3100-1

    #2
    Nahm's louvered door jig was in the Teak Bar episode, which re-aired just a couple of weekends ago on HGTV (looks like your timing is lousy):

    http://www.newyankee.com/getproduct3.cgi?9905

    Having painted more louvered doors than I care to think about, my general attitude about them is, "Never again!" I've never built one but, thinking about the process, the system Nahm devised seems about as simple and as foolproof as it could get.

    BTW, I like your sig line.
    Larry

    Comment

    • RayintheUK
      Veteran Member
      • Sep 2003
      • 1792
      • Crowborough, East Sussex, United Kingdom.
      • Ryobi BT3000

      #3
      Bryan,

      You can get a plan for the jig to rout louvered door mortices at:

      http://www.newyankee.com/getproduct3.cgi?0101

      It will take some time to make - but once, done louvered doors could become your speciality!

      Ray.
      Did I offend you? Click here.

      Comment

      • JR
        The Full Monte
        • Feb 2004
        • 5636
        • Eugene, OR
        • BT3000

        #4
        quote:Originally posted by RayintheUK


        It will take some time to make - but once, done louvered doors could become your speciality!

        Ray.
        Good point, Ray. Then we'd always have a source for louvered doors!

        Go for it, Bryan!

        JR
        JR

        Comment

        • BryanRabb
          Forum Newbie
          • Sep 2004
          • 20
          • Fort Mill, SC, USA.

          #5
          Thanks Guys.
          When in doubt, cut long.

          Comment

          • GeekMom
            Senior Member
            • Dec 2004
            • 752
            • Bonney Lake, WA.
            • Shopsmith Mark V

            #6
            Woodsmith issue #151 has plans for shop-made louvered shutters (p. 16) that might help you get started. Plans for the shutter assembly jig are included (p.25).
            Karen
            <><

            Comment

            • JimD
              Veteran Member
              • Feb 2003
              • 4187
              • Lexington, SC.

              #7
              I've made a couple louvered doors. It turns into two projects. First project is the jig to cut the mortises for the louvers and the second project is the door. If I remember correctly, Norm's jig assumes you want to insert the louvers from the back of the door and cover the back with a little moulding. I made mortises that were not open and then you don't need the moulding. You have a lot tougher time at glue-up, however, because you have to get all the louvers in place. You need a router bit for the mortises, a template guide for the router base, and you just decide on the angle, cut some plywood or MDF for the jig and then make your mortises. It's really pretty easy but it does take awhile.

              Jim

              Comment

              • autiger1
                Senior Member
                • Jan 2003
                • 549
                • Tampa, Florida, USA.

                #8
                Woodline.com has a set of router bits designed for that very purpose...they also have instructions on their site. Might be a good place to start.
                http://www.woodline.com/scripts/prod...?idproduct=627

                Tom

                Comment

                Working...