Do you mark your work? If so, with what?

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts

  • capncarl
    replied
    I sign and write the wood type on the bottom of each of my Tiny Trees, Tables and Mushrooms with a white Jelly Roll pen. Usually I have to scrub the area to be signed with steel wool,, then a quick squirt of Shelac followed by another scrubbing with steel wool, then sign.

    Leave a comment:


  • LCHIEN
    replied
    I have posted about my iron a few times. I think this was the most recent/comprehensive discussion.

    Hank remarked on my branding iron. I've had it for years, Got it from Rockler, its the electric one, at one time they sold one that was heated with a torch. It certainly makes a distinctive addition to any piece. My comments on using it: It takes about 15 minutes to warm up to a good temperature. A long time for an


    Click image for larger version

Name:	fetch?id=840124&d=1620234170.jpg
Views:	204
Size:	86.7 KB
ID:	846961

    Leave a comment:


  • leehljp
    replied
    In the past on my larger items such as book cases, tables, hutches, I would write my name, date and location with a carpenters pencil on the bottom of a table, bottom and top of book cases and hutches. But NOW, I have a branding iron. My daughter asked me to bring it and stamp/brand the things I have made for her. I also added where the board/lumber came from (whose house/office) in special situations. That makes for special memories.

    Leave a comment:


  • Jim Frye
    replied
    Up until about ten years ago, would carve my initials & the year of the build into the back or bottom with a 1/8" ball burr in a Dremel. Then I would fill the carving with wood filler, sand flush and then it got finished with the rest of the piece. Now I print a small label on the PC. I then coat the label on both sides with wiping varnish to seal the ink and plastize the label. This makes the label translucent. To make it opaque, spray the back of the label with white paint. Once cut to size, I glue the label to the inside, back, or bottom of the piece. Then it gets finished over with the rest of the piece. The finished label has an antique look to it from the varnish.
    Click image for larger version

Name:	20211229_143552.jpg
Views:	208
Size:	106.9 KB
ID:	846953
    Click image for larger version  Name:	20211229_143514.jpg Views:	0 Size:	39.4 KB ID:	846951
    Click image for larger version

Name:	20210226_151637.jpg
Views:	224
Size:	135.7 KB
ID:	846952
    Last edited by Jim Frye; 12-29-2021, 02:49 PM. Reason: Added pictures

    Leave a comment:


  • dbhost
    started a topic Do you mark your work? If so, with what?

    Do you mark your work? If so, with what?

    I have been itching since I started setting up my shop and making various projects, to get a makers mark. I've looked at various options, and with gifting occasions upon us, it appears I have been granted that opportunity. However it is an ink stamp makers mark.

    A family member apparently took my workshop logo from my blog page, and had an Etsy maker make a rubber stamp for me. Just got the shipping notification.

    Mind you, some of my favorite MFGs that work with wood products use rubber stamping on their products. Like Fender Musical Instruments, etc....

    I am planning on using a combination of the ink stamp, and sharpie to mark and date a project, and then clear coat over it to protect the mark.

    I literally have waited off of signing / dating a good number of projects as I REALLY wanted this makers mark..

    So, do you mark your projects, and if so, how?
Working...